Kodak KKE PLUS, KKA, JA Slide Transport Malfunctions, Control, Super Lube TL-4276, Cycle Lever

Page 48

SERVICE MANUAL

Slide Transport Malfunctions

Malfunction

 

 

Check

 

 

 

Forward and reverse do not operate using the

1.

Check that the secondary voltage on the

FRONT PANEL BUTTONS or REMOTE

 

MAIN MOTOR is correct.

CONTROL.

2.

Check that the W across the CYCLE

 

 

 

SOLENOID COIL are correct.

 

3.

Check that the voltage across the CYCLE

 

 

SOLENOID is correct.

 

 

 

Forward does not operate, reverse operates,

1.

Check that the CYCLE LEVER and

voltages are correct.

 

RATCHET PLATE are clean. Clean and

 

 

lubricate the parts as necessary. Use

 

 

SUPER LUBE TL-4276.

 

2.

Install a new CAM STACK ASSEMBLY; the

 

 

malfunction is within the CAM.

 

 

 

Reverse does not operate, forward operates,

1.

Do the adjustment for the CYCLE

voltages are correct.

 

SOLENOID.

 

2.

Check that the DIRECTION LEVER

 

 

SPRING is on the DIRECTION LEVER.

 

3.

Check the DIRECTION LEVER for binds.

 

 

Excessive lubrication and dirt can cause

 

 

binds.

 

 

 

Projector does not complete a cycle; FAN

1.

Check for a broken MECHANISM DRIVE

operates.

 

BELT.

 

2.

Check the CYCLE LEVER and RATCHET

 

 

LEVER on the CAM SHAFT ASSEMBLY for

 

 

the following:

 

 

• correct alignment of the CYCLE LEVER

 

 

damage to parts

 

 

lubrication of the CYCLE LEVER (use

 

 

 

SUPER LUBE TL-4276)

 

3.

Check the CYCLE SOLENOID for correct

 

 

operation. See the Voltage chart.

 

 

 

Projector has continual cycle.

1.

Check the CYCLE LEVER for correct

 

 

alignment. See the adjustment for the

 

 

CYCLE LEVER.

 

2.

Check for damage to parts.

 

3.

Check for a short•circuit in the wires:

 

 

Use a tool to hold the CYCLE LEVER

 

 

 

down on the RATCHET LEVER. If

 

 

 

there is a short•circuit causing the

 

 

 

malfunction, the SOLENOID will be

 

 

 

energized. If there is a bind, the CAM

 

 

 

will not rotate.

 

4.

Check that the CAM SHAFT ASSEMBLY

 

 

RATCHET SPRING is installed correctly.

 

5.

If there is a bind in the CAM STACK, install

 

 

a new CAM.

 

 

 

 

48

30APR96 – SM4530-1

Image 48
Contents For Table of Contents Adjusting the Focus Light Path Auto Focus Models PIN Special Application PlugReplacing the Lower Housing Assembly Installing the Lower Housing AssemblyReplacing the FAN Shaft Assembly Remove the Torx Screw from the Blower Cover AssemblyPainted Projector Installing the FAN Shaft Assembly Replacing the MotorInstalling the Motor Replacing the Worm Pulley and Mechanism BeltWorm Pulley Screw Mechanism Belt MotorInstalling the Worm Pulley and Mechanism Belt Replacing the Thermal Fuse AssemblyInstalling the Thermal Fuse Assembly Installing the Lamp Module Receptacle Replacing the Lamp Module ReceptacleReplacing the Cycle Solenoid Assembly Installing the Cycle Solenoid AssemblyPlunger Assembly Pulley ShaftReplacing the Mechanism Assembly Mechanism AssemblyDark Installing the Mechanism Assembly Replacing the AUTO-FOCUS Bracket AssemblyInstalling the AUTO-FOCUS Bracket Assembly Worm Pulley Auto Focusscrew Cyclebracket Solenoid AssemblyReplacing the CAM Stack Assembly and Cycle Lever Assembly Remove the Light Baffle Installing the CAM Stack Assembly and Cycle Lever Assembly Replacing the Lamp Socket Terminal ASSEMBLY, N.P Installing the Lamp Socket Terminal AssemblyReplacing the Lamp Socket Terminal ASSEMBLY, Painted Models Lamp ModuleRetaining Ring Spring Washer Socket PIN Replacing the Lens Mount Assembly Auto Focus Model Installing the Lens Mount Assembly Auto Focus ModelsAUTO-FOCUS Defeat Switch Replacing the Lens Mount Assembly Non Auto Focus Model Installing the Lens Mount Assembly Non Auto Focus ModelReplacing the AUTO-FOCUS Switch Assembly Installing the AUTO-FOCUS Switch AssemblyReplacing the Focus Shaft Assembly Auto Focus Models Lens Mount AssemblyClamp Lever Screw SpringInstalling the Focus Shaft Assembly Replacing the Focus Shaft Assembly Non Auto-Focus ModelsFocus Shaft Spring Assembly Focus Motor Bracket Spacer Installing the Focus Shaft Assembly Adjustment Specification Adjusting the Cycle SolenoidMechanism Assembly BAR Cycle Adjusting the Indexer Lever Assembly Adjusting the Slide Lift Lever Manual Slide Lift Lever Guage TL-3001 SelectAdjusting the Slide Lift Lever Power Adjusting the Zero Position Switch Zero Position Switch NUTAdjusting the Focus Light Path Auto Focus Models Adjustment ToolSpring Hook TL-1165 Auto Focus Bracket Assembly AUTO-FOCUS Target Slide TL-3002Adjusting the Null Projection TAB Lens AUTO-FOCUSTarget Slide Adjusting the Photocell AUTO-FOCUS Assembly Target Slide PADClamp PAD Adjusting the Clamp PAD Assembly Screw NUT Clamp PAD AssemblyAdjusting the Dark Shutter Dark Shutter Pressure PADWorm Pulley Assembly CAM Stack Assembly Cycle Levers FANA0910023HA A0910022DA Adjustment T-BAR AUTO-FOCUS GaugeAUTO-FOCUS Target Slide Super LubeSpecifications PIN Remote Control PIN Special ApplicationsGround Diagnostics Main Motor VoltagesZero Position Switch Shutter SwitchPhotocell Voltages Forward Tray CycleKodak EC-3 Remote Control PIN Remote Cord Plug VoltagesSmall Component Board Assembly 256809 Voltages Power, Illumination, and Cooling Malfunctions Voltage Specifications General PartsSlide Transport Malfunctions ControlSuper Lube TL-4276 Cycle LeverLever Assembly Power Slide Lift LeverEccentrics Direction LeverSwitch Focus Malfunctions Gate Mechanism BoardCheck that the alignment of the Target Eastman Kodak Company
Related manuals
Manual 54 pages 32.2 Kb