Kodak A-61555 manual Safety information, Msds

Page 10

Safety information

Warning labels

CAUTION: Moving parts, avoid contact.

CAUTION: Hot surface, avoid contact.

MSDS	Material Safety Data Sheets (MSDS) are available on the Kodak
	website at: www.kodak.com/go/msds. When accessing the MSDSs
	from the website, you will be required to provide the catalog number of
	the consumable for the Material Safety Data Sheet you are requesting.
	See Chapter 5, “Supplies, consumables and accessories” for
	consumables and catalog numbers.
User precautions	Users and their employer need to observe the common sense
	precautions applicable to the operation of any machinery. These
	include, but are not limited to, the following:
	•	Do not wear loose clothing, unbuttoned sleeves, etc.
	• Do not wear loose jewelry, bracelets, bulky rings, long necklaces, etc.
	•	Hair length should be kept short, using a hair net if needed, or tying
		long hair up in a bundle.
	• Remove all other loose objects from the area that could be drawn into
		the machine.
	•	Take sufficient breaks to maintain mental alertness.
	•	Use only the recommended cleaning supplies.
	•	Do not use canned/compressed air.
	Supervisors should review their practices and make compliance with
	these precautions a part of the job description for operation of the
	scanner or any mechanical device.
Gas springs warning	Do not attempt to repair the gas springs. These are designed to be
	replaced by a Kodak Field Engineer.

1-6	A-61555 April 2009

Image 10

Contents Page Contents Enhanced Printer/Patch Readers Appendix B Introduction New features Scanner features System requirements Supporting documentationContacting Service and Support Phone numbers United States and CanadaSafety information MsdsEMC statements Environmental informationConnection Power systemAcoustic emission NetzanschlußGetting Started Scanner components Front viewPage Page Internal components Rear view Using the Scanner Turning the scanner onApril Document preparation Turning the scanner off Starting and stopping scanningMaterials Page Position Adjusting the input elevatorSelecting your feeding Locking the side guidesPage Adjusting the side guides Adjusting the output trayOutput tray options Page Adjusting the end stop Adjusting the angle of the output trayPage Exit deflector Page Adjusting the short document tray Adjusting the height of the scanner Feeding documents using multi-feed detection Automatic feedingContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen Page Selecting the tone Selecting a language Page Page Image Calibration Udds Calibration Printer units For millimetersFragile Feed mode Idle screen Message windowImage Address information Operator LogAccessing scanner InformationCount only mode Performing a Print test Lowering the elevator Page Select Print Offset. The following screen will be displayed Disabling the PrinterPage Performing a self test Using function keys when scanning ScanningChanging image address levels Automatically pausing and resuming the scanner Manually pausing and resuming the scannerPower Saver mode Viewing messages Resuming from Power Saver modeEnhanced Printer and Patch Readers Enhanced Printer overviewPrinter specifications Font sizeChanging print positions Changing the front horizontal print positionChanging the rear Horizontal print positionPage Page Replacing the ink cartridge Page Replacing the front blotter strips Page Replacing the rear blotter strips Patch Readers Patch function overviewPatch types Patch code placement Toggle PatchMaintenance Cleaning frequency chart Cleaning tools and materials Procedure Start Middle Start of new Day ShiftSupplies, consumables and accessories Ordering partsCleaning procedures Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires Close the printer access cover April Edges of the transport Cleaning the imaging Guides basic cleaningCleaning the imaging guides thorough cleaning Upper imaging guideLower imaging guide Cleaning sheet Running a transportFinal cleaning steps Replacement procedures Align these areas IMPORTANTDo not overstretch the tire it may tear Locking tab Replacing the separation roller or separation roller tires Replacing the imaging Replacing the preSeparation pad GuidesTroubleshooting Accessing Operator LogAccessing the Operator Log from the Scan Validation tool Page Page Message listing ID#Enhanced Printer and Patch Readers for more Image Processing Guide for valid values Informational message. The pod was closed April Numerical message Contacting Service Problem solving Problem Possible SolutionIf you are using iThresholding, reduce the Contrast value Background Accessory Kodak Manual Feeder Ultralightweight Paper Feed ModuleResolution Printer Accessory Appendix B Specifications