Kodak A-61555 manual

Page 64

Moving the printer carrier and cable from the front to the rear or vice versa

The scanner comes with the printer carrier and ribbon cable installed for front pre-scan printing. If your application requires rear post-scan printing, the printer carrier and cable must be moved from the front to the rear position. Printing can only be done on the front or the rear.

If you alternate between front and rear printing frequently, you may want to purchase a second printer carrier, then you only need to move the ink cartridge from the front to the back or vice versa. Otherwise, you need to move the printer carrier and cable from the front to rear or rear to front as well as the ink cartridge.

NOTE: After you move the printer carrier and cable you must restart the scanner.

Moving the printer carrier and cable from front position to the rear position

NOTE: Remove the ink cartridge before you begin. See the next section “Replacing the ink cartridge” for procedures.

1.Access the front printer by removing the output tray and lifting the printer access cover.

2.Disconnect the ribbon cable by pulling it straight out from the holder.

3.Lift the printer carrier out of position.

4.Close the printer access cover and reinstall the output tray.

5.Access the rear printer by lifting the top access cover.

6.Install the printer carrier in the desired position.

7.Connect the ribbon cable.

8.Install the ink cartridge. See the next section, “Replacing the ink cartridge” for procedures.

9.Close the top access cover.

10.Restart the scanner.

11.Run a test print.

A-61555 April 2009

4-5

Image 64

Contents Page Contents Enhanced Printer/Patch Readers Appendix B Introduction New features Scanner features System requirements Supporting documentationContacting Service and Support Phone numbers United States and CanadaSafety information MsdsEMC statements Environmental informationPower system Acoustic emissionConnection NetzanschlußGetting Started Scanner components Front viewPage Page Internal components Rear view Using the Scanner Turning the scanner onApril Document preparation Turning the scanner off Starting and stopping scanningMaterials Page Adjusting the input elevator Selecting your feedingPosition Locking the side guidesPage Adjusting the side guides Adjusting the output trayOutput tray options Page Adjusting the end stop Adjusting the angle of the output trayPage Exit deflector Page Adjusting the short document tray Adjusting the height of the scanner Feeding documents using multi-feed detection Automatic feedingContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen Page Selecting the tone Selecting a language Page Page Image Calibration Udds Calibration Printer units For millimetersFragile Feed mode Idle screen Message windowImage Address information Operator LogAccessing scanner InformationCount only mode Performing a Print test Lowering the elevator Page Select Print Offset. The following screen will be displayed Disabling the PrinterPage Performing a self test Using function keys when scanning ScanningChanging image address levels Automatically pausing and resuming the scanner Manually pausing and resuming the scannerPower Saver mode Viewing messages Resuming from Power Saver modeEnhanced Printer and Patch Readers Enhanced Printer overviewPrinter specifications Font sizeChanging print positions Changing the front horizontal print positionChanging the rear Horizontal print positionPage Page Replacing the ink cartridge Page Replacing the front blotter strips Page Replacing the rear blotter strips Patch Readers Patch function overviewPatch types Patch code placement Toggle PatchMaintenance Cleaning frequency chart Cleaning tools and materials Procedure Start Middle Start of new Day ShiftSupplies, consumables and accessories Ordering partsCleaning procedures Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires Close the printer access cover April Edges of the transport Cleaning the imaging Guides basic cleaningCleaning the imaging guides thorough cleaning Upper imaging guideLower imaging guide Cleaning sheet Running a transportFinal cleaning steps Replacement procedures Align these areas IMPORTANTDo not overstretch the tire it may tear Locking tab Replacing the separation roller or separation roller tires Replacing the pre Separation padReplacing the imaging GuidesTroubleshooting Accessing Operator LogAccessing the Operator Log from the Scan Validation tool Page Page Message listing ID#Enhanced Printer and Patch Readers for more Image Processing Guide for valid values Informational message. The pod was closed April Numerical message Contacting Service Problem solving Problem Possible SolutionIf you are using iThresholding, reduce the Contrast value Background Accessory Kodak Manual Feeder Ultralightweight Paper Feed ModuleResolution Printer Accessory Appendix B Specifications