Kodak A-61555 manual Toggle Patch, Patch code placement

Page 72

Toggle Patch

Image addressing - enabled

Image addressing - disabled

When image addressing is disabled, the Patch Readers are also disabled. However a Toggle patch can still be detected.

Patch Types 2, 3 and T — these patch types are used for image addressing.

The Patch Readers control document level changes by automatically sensing a predefined patch code and changing the document level accordingly.

IMPORTANT: Do not use these illustrated patches for production — they are not to spec.

Patch 2 — assigns a Level 2 to the current document

Patch 3 — assigns a Level 3 to the current document

Patch 5/T/Transfer Patch — assigns a predetermined level to the next document

	The Transfer Patch Definition is also defined by the application. The
	Transfer Patch Definition controls the level assigned to the next
	document when a Transfer Patch is used. For example, if the Transfer
	Patch Definition for the current operation is defined as Level 3 and a
	Transfer Patch is used, the next document will be assigned Level 3.
Patch code placement	See Kodak publication A-61599, Patch Code Information, for complete
	information about patch placement and specifications.
	Patches can be tested using the Patch Test on the touchscreen. See
	Chapter 3, “Performing a Patch test” for more information.

A-61555 April 2009

4-13

Image 72

Contents Page Contents Enhanced Printer/Patch Readers Appendix B Introduction New features Scanner features System requirements Supporting documentationContacting Service and Support Phone numbers United States and CanadaSafety information MsdsEMC statements Environmental informationPower system Acoustic emissionConnection NetzanschlußGetting Started Scanner components Front viewPage Page Internal components Rear view Using the Scanner Turning the scanner onApril Turning the scanner off Starting and stopping scanning Document preparationMaterials Page Adjusting the input elevator Selecting your feedingPosition Locking the side guidesPage Adjusting the output tray Adjusting the side guidesOutput tray options Page Adjusting the end stop Adjusting the angle of the output trayPage Exit deflector Page Adjusting the short document tray Adjusting the height of the scanner Feeding documents using multi-feed detection Automatic feedingContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen Page Selecting the tone Selecting a language Page Page Image Calibration Udds Calibration Printer units For millimetersFragile Feed mode Idle screen Message windowImage Address information Operator LogAccessing scanner InformationCount only mode Performing a Print test Lowering the elevator Page Select Print Offset. The following screen will be displayed Disabling the PrinterPage Performing a self test Using function keys when scanning ScanningChanging image address levels Automatically pausing and resuming the scanner Manually pausing and resuming the scannerPower Saver mode Viewing messages Resuming from Power Saver modeEnhanced Printer and Patch Readers Enhanced Printer overviewPrinter specifications Font sizeChanging print positions Changing the front horizontal print positionChanging the rear Horizontal print positionPage Page Replacing the ink cartridge Page Replacing the front blotter strips Page Replacing the rear blotter strips Patch function overview Patch ReadersPatch types Patch code placement Toggle PatchMaintenance Cleaning frequency chart Cleaning tools and materials Procedure Start Middle Start of new Day ShiftSupplies, consumables and accessories Ordering partsCleaning procedures Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires Close the printer access cover April Edges of the transport Cleaning the imaging Guides basic cleaningCleaning the imaging guides thorough cleaning Upper imaging guideLower imaging guide Cleaning sheet Running a transportFinal cleaning steps Replacement procedures Align these areas IMPORTANTDo not overstretch the tire it may tear Locking tab Replacing the separation roller or separation roller tires Replacing the pre Separation padReplacing the imaging GuidesTroubleshooting Accessing Operator LogAccessing the Operator Log from the Scan Validation tool Page Page Message listing ID#Enhanced Printer and Patch Readers for more Image Processing Guide for valid values Informational message. The pod was closed April Numerical message Contacting Service Problem solving Problem Possible SolutionIf you are using iThresholding, reduce the Contrast value Ultralightweight Paper Feed Module Background Accessory Kodak Manual FeederResolution Printer Accessory Appendix B Specifications