Kodak A-61555 manual

Page 23

Adjusting the height of the input elevator

Adjusting the input tray for document length

The input elevator can be set to accommodate stacks of 25-, 100-, 250- or 500-documents of 20 lb. bond paper. Input elevator settings are made through the TWAIN Data source or ISIS Driver.

NOTE: In this document 25 will be referred to as the highest setting and 500 as the lowest.

Make this setting based on the number of documents you will place in the input elevator at one time.

When set to 25 (Document Feeder or Normal), the input elevator will remain in position. When set to 100, 250 or 500, the input elevator will automatically raise to feed documents and lower after the last document in your stack has been fed.

•No adjustments are required for documents up to 14 inches long.

•If you are scanning documents from 14 to 17 inches in length, open the input elevator extension.

•Documents longer than 17 inches require a document extender. Three sizes of document extenders are available for scanning documents from 43 cm (17 in.) to 86 cm (34 in.). See the section entitled, “Ordering parts” in Chapter 5 or contact your Kodak Field Engineer at 1-800-3KODAK3 (1-800-356-3253).

3-6	A-61555 April 2009

Image 23

Contents Page Contents Enhanced Printer/Patch Readers Appendix B Introduction New features Scanner features Supporting documentation System requirementsPhone numbers United States and Canada Contacting Service and SupportMsds Safety informationEnvironmental information EMC statementsNetzanschluß Power systemAcoustic emission ConnectionScanner components Front view Getting StartedPage Page Internal components Rear view Turning the scanner on Using the ScannerApril Materials Turning the scanner off Starting and stopping scanningDocument preparation Page Locking the side guides Adjusting the input elevatorSelecting your feeding PositionPage Output tray options Adjusting the output trayAdjusting the side guides Page Adjusting the angle of the output tray Adjusting the end stopPage Exit deflector Page Adjusting the short document tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feed detectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen Page Selecting the tone Selecting a language Page Page Image Calibration Udds Calibration For millimeters Printer unitsFragile Feed mode Message window Idle screenOperator Log Image Address informationInformation Accessing scannerCount only mode Performing a Print test Lowering the elevator Page Disabling the Printer Select Print Offset. The following screen will be displayedPage Performing a self test Scanning Using function keys when scanningChanging image address levels Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview Enhanced Printer and Patch ReadersFont size Printer specificationsChanging the front horizontal print position Changing print positionsHorizontal print position Changing the rearPage Page Replacing the ink cartridge Page Replacing the front blotter strips Page Replacing the rear blotter strips Patch types Patch function overviewPatch Readers Toggle Patch Patch code placementMaintenance Procedure Start Middle Start of new Day Shift Cleaning frequency chart Cleaning tools and materialsOrdering parts Supplies, consumables and accessoriesCleaning procedures Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires Close the printer access cover April Edges of the transport Guides basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides thorough cleaningLower imaging guide Running a transport Cleaning sheetFinal cleaning steps Replacement procedures Align these areas IMPORTANTDo not overstretch the tire it may tear Locking tab Replacing the separation roller or separation roller tires Guides Replacing the preSeparation pad Replacing the imagingAccessing Operator Log TroubleshootingAccessing the Operator Log from the Scan Validation tool Page Page ID# Message listingEnhanced Printer and Patch Readers for more Image Processing Guide for valid values Informational message. The pod was closed April Numerical message Contacting Service Problem Possible Solution Problem solvingIf you are using iThresholding, reduce the Contrast value Resolution Printer Accessory Ultralightweight Paper Feed ModuleBackground Accessory Kodak Manual Feeder Appendix B Specifications