Kodak A-61555 manual April

Page 101

Messages	ID#	Operator Message
UDDS calibration failed	333	The UDDS calibration failed.
		• Be sure you are using the correct ultrasonics calibration target.
		See Chapter 3, “Calibrating the scanner”.
		• Clean the sensors and try again.
		• If the problem persists, call Service.
UDDS calibration succeeded	332	Informational message. The scanner ultrasonics has been
		successfully calibrated.

UDDS is not calibrated	21	• Perform an Ultrasonics calibration. See Chapter 3, “Calibrating
		the scanner” for procedures.

UDDS multi-feed detected	23, 24, 334	A multi-feed document condition has been detected.
		• Check the host monitor to see if there are any overlapped
		documents that may need to be rescanned.
		This condition may be caused by:
		• Poor document separation causing overlapped documents.
		• Stickers on the documents.
		• Wrinkles in the documents
		• Thick documents with high multi-feed settings.

Unable to scan	5	• The previous error condition has not been corrected. For
		example, there could be a document jam that has not been
		completely cleared.
		• Incomplete or conflicting image processing parameters.
		• See other log entries for the actual condition.

A-61555 April 2009

6-9

Image 101

Contents Page Contents Enhanced Printer/Patch Readers Appendix B Introduction New features Scanner features Supporting documentation System requirementsPhone numbers United States and Canada Contacting Service and SupportMsds Safety informationEnvironmental information EMC statementsAcoustic emission Power systemConnection NetzanschlußScanner components Front view Getting StartedPage Page Internal components Rear view Turning the scanner on Using the ScannerApril Materials Turning the scanner off Starting and stopping scanningDocument preparation Page Selecting your feeding Adjusting the input elevatorPosition Locking the side guidesPage Output tray options Adjusting the output trayAdjusting the side guides Page Adjusting the angle of the output tray Adjusting the end stopPage Exit deflector Page Adjusting the short document tray Adjusting the height of the scanner Automatic feeding Feeding documents using multi-feed detectionContinuous feeding Manual feeding Feeding documents that require special handling Using the operator control panel touchscreen Settings screen Page Selecting the tone Selecting a language Page Page Image Calibration Udds Calibration For millimeters Printer unitsFragile Feed mode Message window Idle screenOperator Log Image Address informationInformation Accessing scannerCount only mode Performing a Print test Lowering the elevator Page Disabling the Printer Select Print Offset. The following screen will be displayedPage Performing a self test Scanning Using function keys when scanningChanging image address levels Manually pausing and resuming the scanner Automatically pausing and resuming the scannerResuming from Power Saver mode Power Saver mode Viewing messagesEnhanced Printer overview Enhanced Printer and Patch ReadersFont size Printer specificationsChanging the front horizontal print position Changing print positionsHorizontal print position Changing the rearPage Page Replacing the ink cartridge Page Replacing the front blotter strips Page Replacing the rear blotter strips Patch types Patch function overviewPatch Readers Toggle Patch Patch code placementMaintenance Procedure Start Middle Start of new Day Shift Cleaning frequency chart Cleaning tools and materialsOrdering parts Supplies, consumables and accessoriesCleaning procedures Cleaning the rollers Cleaning the separation roller tires Cleaning the feed module tires Close the printer access cover April Edges of the transport Guides basic cleaning Cleaning the imagingUpper imaging guide Cleaning the imaging guides thorough cleaningLower imaging guide Running a transport Cleaning sheetFinal cleaning steps Replacement procedures Align these areas IMPORTANTDo not overstretch the tire it may tear Locking tab Replacing the separation roller or separation roller tires Separation pad Replacing the preReplacing the imaging GuidesAccessing Operator Log TroubleshootingAccessing the Operator Log from the Scan Validation tool Page Page ID# Message listingEnhanced Printer and Patch Readers for more Image Processing Guide for valid values Informational message. The pod was closed April Numerical message Contacting Service Problem Possible Solution Problem solvingIf you are using iThresholding, reduce the Contrast value Resolution Printer Accessory Ultralightweight Paper Feed ModuleBackground Accessory Kodak Manual Feeder Appendix B Specifications