Oki 1.2 manual Select outgoing destination, Description Default, Neglect first, Digit is not

Page 34

Select outgoing destination

•Selecting an outgoing destination is available only when Use PSTN line is selected. If it is not selected, all outgoing calls are via the VoIP line, without neglecting the first digit of the phone number.

Item	Description		Default
Select	• Select Use PSTN line, Use VoIP line or Unavailable to dial	0	PSTN line
outgoing	the first digit of an outgoing destination telephone number.	1	PSTN line
destination	• Selection can also be made to Neglect the first digit or not	2	VoIP line
	to do so at the same time.	3	VoIP line

•Select Use PSTN line to use the PSTN line for outgoing calls. 4 VoIP line

•Selecting Unavailable to dial will not allow any outgoing calls. 5 VoIP line

• Select Use VoIP line to use the VoIP line for outgoing calls.	6	VoIP line
• When the selection is made to neglect the first digit, the	7	VoIP line
first digit is not recognized as a part of the outgoing	8	VoIP line
destination telephone number.	9	VoIP line
• An asterisk (*) cannot be used as a part of an outgoing	# VoIP line
telephone number.	Neglect first
	digit is not
	selected.

Default values, set at the time of product shipping, are displayed when the Restore default button is clicked.

26Setup

Image 34

Contents

Installation Guide VersionSafety Warning Page Contents Setup VoIP-TA setting Window Important Equipment InformationImportant Safety Instructions Important Safety Instructions Introduction Welcome to the world of Oki Internet telephony…Outline FeaturesVoIP-TA Front Panel LEDsConnectors Back PanelMode When using both IP and PstnWhen using IP network only StatusAnalogue telephone or G3 facsimile equipment II InstallationConnections Analogue PstnPower source Personal computer PCDuring installation During useVia an IP Network III Placing CallsGeneral Operation Services Third party incoming call during another callEnd-to-end service using Dtmf signaling Call transfer during a telephone callPlacing Calls How to register the absent service Absent serviceHow to cancel the absent service Line selection Details of ServicesUsing both a Pstn line and the IP network Third party incoming call during another callFor Pstn line not receiving services using hookflash hooking Power failure switching Identification of incoming callSetting IP Address Using the IP network onlyTranslating IP Address for VoIP Installing the Maintenance Console Software IV SetupMaintenance Console Software Requirements Maintenance Console Software CompatibilityMode Function Functions of the Maintenance Console SoftwareData Setup Procedure Password, see Chapter V,Activating and Deactivating the Software’s Functions New connection window will appear Changing Modes and Setup Conditions Changing to the Setup modeChanging setup conditions Saving all setup conditions in a file Reading information From the file Select outgoing destination below Basic settings for Pstn lineDescriptions Default For Pstn lineSelect Use Pstn line, Use VoIP line or Unavailable to dial Description DefaultSelect outgoing destination Neglect first1st Outgoing Neglect Digit Destination 1st digit Dailing IP address NumberDialed, excluding the first digit and 567 connects the call Number VoIP-TA operation DialedDialed, excluding the first digit and 901 connects the call Dialed, excluding the first digit and 789 connects the callDetailed settings for Pstn line Network settings UDP port No Specifies the UDP port number for communication Network Address Translation NAT Global address spaceStatic IP Masquerade with port number translations Gatekeeper settings To select Unicast GRQ or Multicast GRQ whenDetailed Gatekeeper settings BRQ DRQ GRQAddress table Sorting the list using each row as a key Sort with keyAddress table display editing Setup Description DetailsButton see pages 42 Voice settings RTP/RTCPSetting ms Byte Voice codec setting and bandwidth usedVoice codec FAX setting TCP/UDPSlic setting Functions of the Maintenance Console Software MaintenanceVerifying the Software Version Information Checking the Operation Status of the VoIP-TA Display Displayed contents Description Explanation of the displayed informationUpdating Unit Programs Changing the password Remote mode VI TroubleshootingSymptom Items to check Local modeUsage VII SpecificationsPort number Important Equipment Information Warranty Period Warranty and ServiceFollowing the warranty period Oki Service Offices London Office