Oki 1.2 manual Important Safety Instructions

Page 7

•Do not use AC adapters other than those specified or supplied.

•If liquid enters the unit, immediately disconnect the power plug (by grasping the power plug, not the cord) from the power outlet and contact an authorized sales agent or service provider. Continued use may result in fire or electric shock.

•If smoke or fumes are emitted from the unit, immediately disconnect the AC plug (by grasping the power plug, not the cord). When smoke emissions cease, contact a sales agent or service office for repair.

Continued use may cause fire, electric shock or unit failure.

•Use only authorized sales agents or service offices for internal inspection or repair.

CAUTION Incorrect use by neglecting the following instructions may cause fire, electric shock, unit failure resulting in injury or damage.

•Avoid oily, humid or dusty locations, such as on a kitchen table or near a humidifier.

•Do not place the unit on unstable or inclined surfaces as the unit may fall.

•Avoid locations exposed to direct sunlight or moisture as internal overheating may occur causing fire or unit failure.

•Wipe away with a dry cloth any water droplets that may be on the surface of the unit. Water intrusion may cause fire or unit failure.

•Do not cover up the vent holes of the VoIP-TA. If covered, internal overheating may result causing fire or unit failure.

•Do not unplug the AC power plug by pulling on the cord. Always grasp the plug portion when disconnecting the AC power plug.

•Disconnect the AC power cord and other connectors when moving the VoIP-TA.

•For safety, disconnect the AC plug from the power supply outlet (by grasping the power plug, not the cord) before starting maintenance.

Important Safety Instructions	vi

Image 7

Contents

Version Installation GuideSafety Warning Page Contents Important Equipment Information Setup VoIP-TA setting WindowImportant Safety Instructions Important Safety Instructions Welcome to the world of Oki Internet telephony… IntroductionOutline FeaturesVoIP-TA LEDs Front PanelBack Panel ConnectorsStatus When using both IP and PstnWhen using IP network only ModeAnalogue Pstn II InstallationConnections Analogue telephone or G3 facsimile equipmentPersonal computer PC Power sourceDuring use During installationVia an IP Network III Placing CallsGeneral Operation Third party incoming call during another call ServicesCall transfer during a telephone call End-to-end service using Dtmf signalingPlacing Calls How to register the absent service Absent serviceHow to cancel the absent service Third party incoming call during another call Details of ServicesUsing both a Pstn line and the IP network Line selectionFor Pstn line not receiving services using hookflash hooking Identification of incoming call Power failure switchingSetting IP Address Using the IP network onlyTranslating IP Address for VoIP Maintenance Console Software Compatibility IV SetupMaintenance Console Software Requirements Installing the Maintenance Console SoftwarePassword, see Chapter V, Functions of the Maintenance Console SoftwareData Setup Procedure Mode FunctionActivating and Deactivating the Software’s Functions New connection window will appear Changing to the Setup mode Changing Modes and Setup ConditionsChanging setup conditions Saving all setup conditions in a file Reading information From the file For Pstn line Basic settings for Pstn lineDescriptions Default Select outgoing destination belowNeglect first Description DefaultSelect outgoing destination Select Use Pstn line, Use VoIP line or Unavailable to dialDailing IP address Number 1st Outgoing Neglect Digit Destination 1st digitDialed, excluding the first digit and 789 connects the call Number VoIP-TA operation DialedDialed, excluding the first digit and 901 connects the call Dialed, excluding the first digit and 567 connects the callDetailed settings for Pstn line Network settings UDP port No Specifies the UDP port number for communication Global address space Network Address Translation NATStatic IP Masquerade with port number translations To select Unicast GRQ or Multicast GRQ when Gatekeeper settingsBRQ DRQ GRQ Detailed Gatekeeper settingsAddress table Sorting the list using each row as a key Sort with keyAddress table display editing Setup Description DetailsButton see pages 42 RTP/RTCP Voice settingsSetting ms Byte Voice codec setting and bandwidth usedVoice codec TCP/UDP FAX settingSlic setting Functions of the Maintenance Console Software MaintenanceVerifying the Software Version Information Checking the Operation Status of the VoIP-TA Explanation of the displayed information Display Displayed contents DescriptionUpdating Unit Programs Changing the password Local mode VI TroubleshootingSymptom Items to check Remote modeUsage VII SpecificationsPort number Important Equipment Information Warranty Period Warranty and ServiceFollowing the warranty period London Office Oki Service Offices