Emerson CC1000DM user manual Identification Numbers Connectors

Page 22

2

Identification Numbers

Connectors

S E T U P

CC1000dm Circuit Board

Before you install the CC1000dm circuit board in a system, you should record the fol- lowing information:

The board serial number: 680– ______________________________________ . The board serial number appears on a bar code sticker located on the back of the board.

The board product identification: ___________________________________ . This sticker is located near the board serial number.

It is useful to have these numbers available when you contact the Technical Support department at Artesyn Communication Products.

The CC1000dm circuit board has various connectors (see the figures beginning on page 2 -3), summarized as follows:

P1–P2:These connectors are not installed on the CC1000dm.

J1: This 110-pin connector has keying for 3.3 volt and 5 volt supplies. See Table 4-3for the pin assignments.

J2: This 110-pin connector carries the PCI 64-bit extension signals. See Table 4-4for the pin assignments.

J3: This is a 95-pin connector that routes the I/O signals for the PMC I/O, serial port, and USB port. See Table 4-5for the pin assignments.

J5: This 110-pin connector is used for PMC I/O. See Table 4-6for the pin assignments.

J6: This is a 3-pin header for the Hot Swap switch.

J11: This connector shares the 32-bit PCI signals with the J12 connector (secondary bus). In addition, J11 supports a V(I/O) power supply for universal PCI signaling. It uses 3.3 volt PCI buffers with a 5 volt tolerance. See Table 3-9for the pin assignments.

J12: This connector shares the 32-bit PCI signals with the J11 connector (secondary bus). It also carries the 3.3 volt supply voltage. See Table 3-9for the pin assignments.

J13: This connector carries the 64-bit PCI extensions (secondary bus). See Table 3-9for the pin assignments.

J14: This connector is for user I/O, which routes to J3. See Table 3-9for the pin assignments.

J21: This connector shares the 32-bit PCI signals with the J22 connector (secondary bus). In addition, J21 supports a V(I/O) power supply for universal PCI signaling. It uses 3.3 volt PCI buffers with a 5 volt tolerance. See Table 3-10for the pin assignments.

J22: This connector shares the 32-bit PCI signals with the J21 connector (secondary bus). It also carries the 3.3 volt supply. See Table 3-10for the pin assignments.

2-4CC1000dm User’s Manual

10004281-02

Image 22
Contents CC1000dm Revision Level Principal Changes Date Regulatory Agency Warnings & Notices EC Declaration of Conformity Contents PCI Bridge Features PMC Module Installation Bridge EepromFigures G u r e s Tables Ta b l e s Registers G i s t e r s Overview N. .C.T.I.O. N. .A. L. . O. .V.E. R. .V.I.E.W Functional OverviewProduct Certification Type SpecificationRoHS Compliance Additional Information Terminology and NotationTechnical References Device / Interface DocumentDocument 6CC1000dm User’s Manual 10004281-02 Setup Width DepthCC1000dm Circuit Board Component Map, Top revCC1000dm Circuit Board Identification Numbers Connectors Fuses and Jumpers Jumper/Header Locations, Top View CC1000dm Setup Multiple Option Selection JP3CC1000dm Setup Signal Name Bit SelectionBit Selection Jumper Signal NamePin Signal Jumper Position ModeSelOperational Checks Power RequirementsEnvironmental Considerations Typical Current Voltage Range AmpsS. E. .T. .M. E. .T.H. O. .D.S Reset Methods Non-transparentTroubleshooting O. U. .B. L. E. .S.H. O. .O. T. I. N. .G14CC1000dm User’s Manual 10004281-02 PMC/PCI Interface C / P C I I N T E R F a C E PMC Module InstallationDevice Mapping VoltsBase PCI Base cPCI Interrupt Transparent Mode Assignment SecondaryTiming Interrupts Interrupt System controller modesInternal Arbiter Control Register CC1000dm Request/Grant Local PCI Bus Device I.D. G. .E. .E.E. P. .R.O. M Bridge EepromPCI 6254 Configuration Registers PCI 6254 Configuration Registers Power Management CSR38h Reserved Status PCI Identification Values PCI 6254 Bridge ModeVendor Device Subsystem ID hex PCI Bus Control Signals I. .B.U. S. . C. .O. N. .T.R. O. .L. .S.I.G. N. .A.L. SPCI Bus Control Signals PMC Connector Pin Assignments Pin J11 J12 J13 J14Pin J21 Pin J11J13 J14 Pin J11 J12 J23 J24 Pin J21 J22Pin J21 J22 J23 J24 Carrier Card BUS Interface O. C. .K. .G. E. .N. E. R. .A.T. I.O. .N Arbitration and Device SelectionHot Swap Model DescriptionImplementation Hot SwapSignal Description CC1000dm Control SignalsPin Row Z Row a Row B Row C Row D Row E Row F Backplane Connector Pin Assignments Pin Row Z Row a Row B Row C Row D Row ERow F Pin Row a Row B Row C Row D Row E Row FPin Row a Row B Row C Row D Row E Backplane Connector Pin Assignments 10CC1000dm User’s Manual 10004281-02 CPCI PrPMCO s s a r y Index D e Page W. a r t e s y n c p . c o m