Emerson CC1000DM Device Mapping, PMC Module Installation, C / P C I I N T E R F a C E, Volts

Page 34

3

Table 3-1:

PMC Slots Available Power

Note:

A maximum load current of 6 amps (worst case) results in a voltage drop of approximately 100 mV to the PMC 5 volt power supply inputs. To ensure proper module operation, adjust the CompactPCI power supply to accommodate any voltage drop or power supply ripple that may occur when operating the carrier card.

P M C / P C I I N T E R F A C E

PMC Module Installation

3.3 Volts:

5 Volts:

 

3 3 and 5 Volts Combined:

. . . . . . . . . .

. . . . . . . . . .

 

. . . . . . . . . . . . . . . .

 

8.5 amps

6 amps

 

28-30 watts

 

 

 

 

2To prevent ESD damage to the CC1000dm carrier card and the PMC modules, wear a grounding wriststrap and use a grounded work surface while handling the card.

3Set up the PMC module and install it on the CC1000dm carrier card as specified in the module’s hardware manual.

Monarch Functionality Each slot (PMC1 and PMC2) on the CC1000dm carrier card can be configured to func- tion as either a Monarch or non-Monarch PMC slot (in non-transparency or legacy mode), as described in the Processor PMC Standard for Processor PCI Mezzanine Cards, VITA 32- 2003 Specification. Although only one slot can be a Monarch, there can be as many non-Monarch PMCs as the carrier card can support. A module placed on the Monarch slot performs local PCI bus enumeration and handles PMC interrupts. A mod- ule placed on the non-Monarch slot behaves in the traditional slave processor manner. Both slots have the ability to be configured as either Monarch or non-Monarch by the 10-pin jumper at JP3.

Device Mapping

Table 3-2:

IDSEL Mapping for PCI

Devices

Once the Monarch PMC module has completed initialization of the CC1000dm local bus, the PCI agents located on that bus are available for access. There are up to two PCI devices installed on the PLX PCI 6254 (HB6) secondary bus and two PCI IDSEL lines allocated to each PMC slot. Table 3-2lists all the IDSEL mappings.

PCI Address Line: Local PCI Device IDSEL Connection:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AD22

PMC 1

 

 

AD21

PMC 1 Alternate Device

 

 

AD20

PMC 2

 

 

AD19

PMC 2 Alternate Device

 

 

AD18

PLX PCI 6254 (HB6) PCI Bridge

 

 

3-2CC1000dm User’s Manual

10004281-02

Page 33 Page 35
Image 34
Page 33 Page 35
Contents CC1000dm Revision Level Principal Changes Date Regulatory Agency Warnings & Notices EC Declaration of Conformity Contents PCI Bridge Features PMC Module Installation Bridge EepromFigures G u r e s Tables Ta b l e s Registers G i s t e r s Overview N. .C.T.I.O. N. .A. L. . O. .V.E. R. .V.I.E.W Functional OverviewProduct Certification Type SpecificationRoHS Compliance Additional Information Terminology and NotationTechnical References Device / Interface DocumentDocument 6CC1000dm User’s Manual 10004281-02 Setup Width DepthCC1000dm Circuit Board Component Map, Top revCC1000dm Circuit Board Identification Numbers Connectors Fuses and Jumpers Jumper/Header Locations, Top View CC1000dm Setup Multiple Option Selection JP3CC1000dm Setup Signal Name Bit SelectionBit Selection Jumper Signal NamePin Signal Jumper Position ModeSelOperational Checks Power RequirementsEnvironmental Considerations Typical Current Voltage Range AmpsS. E. .T. .M. E. .T.H. O. .D.S Reset Methods Non-transparentTroubleshooting O. U. .B. L. E. .S.H. O. .O. T. I. N. .G14CC1000dm User’s Manual 10004281-02 PMC/PCI Interface C / P C I I N T E R F a C E PMC Module InstallationDevice Mapping VoltsBase PCI Base cPCI Interrupt Transparent Mode Assignment SecondaryTiming Interrupts Interrupt System controller modesInternal Arbiter Control Register CC1000dm Request/Grant Local PCI Bus Device I.D. G. .E. .E.E. P. .R.O. M Bridge EepromPCI 6254 Configuration Registers PCI 6254 Configuration Registers Power Management CSR38h Reserved Status PCI Identification Values PCI 6254 Bridge ModeVendor Device Subsystem ID hex PCI Bus Control Signals I. .B.U. S. . C. .O. N. .T.R. O. .L. .S.I.G. N. .A.L. SPCI Bus Control Signals PMC Connector Pin Assignments Pin J11 J12 J13 J14Pin J21 Pin J11J13 J14 Pin J11 J12 J23 J24 Pin J21 J22Pin J21 J22 J23 J24 Carrier Card BUS Interface O. C. .K. .G. E. .N. E. R. .A.T. I.O. .N Arbitration and Device SelectionHot Swap Model DescriptionImplementation Hot SwapSignal Description CC1000dm Control SignalsPin Row Z Row a Row B Row C Row D Row E Row F Backplane Connector Pin Assignments Pin Row Z Row a Row B Row C Row D Row ERow F Pin Row a Row B Row C Row D Row E Row FPin Row a Row B Row C Row D Row E Backplane Connector Pin Assignments 10CC1000dm User’s Manual 10004281-02 CPCI PrPMCO s s a r y Index D e Page W. a r t e s y n c p . c o m
Top Page Image Contents