2. Printer Settings (20 ppm copier)
Item No. | Item | Display message | Available settings | Remarks |
|
|
|
|
|
23 | Page Protect | Page Protect | Auto, On |
|
| If “AUTO” is selected here, the machine will |
|
|
|
| monitor the data and, if necessary, will |
|
|
|
| automatically turn Page Protect ON. If a |
|
|
|
| “Print overrun” error does happen to occur |
|
|
|
| even then, the machine will automatically |
|
|
|
| change the Page Protect setting to “ON”. |
|
|
|
|
|
|
|
|
24 | Line Feed (LF) handling | LF Action | LF only, | Allows you to set different line |
|
|
| CR and LF, | feed handling for the parallel |
|
|
| Ignore LF | interface and the Network Card |
|
|
|
| (option). Select the desired |
|
|
|
| interface under the “Interface |
|
|
|
| selection” setting (item No.: 2). |
|
|
|
|
|
25 | Carriage Return (CR) handling | CR Action | CR only, | Allows you to set different carriage |
|
|
| CR and LF, | return handling for the parallel |
|
|
| Ignore CR | interface and the Network Card |
|
|
|
| (option). Select the desired |
|
|
|
| interface under the “Interface |
|
|
|
| selection” setting (item No.: 2). |
|
|
|
|
|
26 | Wide A4 ON/OFF | Wide A4 | On, Off |
|
| Increases the printing area on A4 size paper. |
|
|
|
|
|
|
|
|
27 | Smoothing ON/OFF | KIR Mode | On, Off |
|
| Allows a printing resolution of an interpo- |
|
|
|
| lated 2400 dpi x 600 dpi through the |
|
|
|
| smoothing process. |
|
|
|
|
|
|
|
|
28 | Draft Mode ON/OFF | Draft | On, Off |
|
| Allows printing in a |
|
|
|
| mode is especially suited for test pages, etc., |
|
|
|
| where high printing quality is not required. |
|
|
|
|
|
|
|
|
29 | Printing resolution | Resolution | 300 dpi, 600 dpi |
|
|
|
|
|
|
30 | RAM disk ON/OFF | RAM DISK Mode | On, Off | At least 16 MB of additional |
|
|
|
| memory (option) must be installed. |
|
|
|
|
|
31 | RAM disk size | RAM DISK Size | 01 - 99 (MBytes) | Displayed only when “On” is |
| Sets the amount of memory that will be used |
|
| selected under the “RAM disk ON/ |
| as a RAM disk. The maximum size that can |
|
| OFF” setting (item No.: 30). |
| be selected is the total amount of memory |
|
|
|
| installed minus the amount used by the |
|
|
|
| system (9 MB). |
|
|
|
|
|
|
|
|
32 | Reading data | Read Data | Select the name of | Displayed only when there is |
| Reads the selected data on the RAM disk. |
| the partition which | appropriate data in the RAM disk. |
|
|
| holds the data from |
|
|
|
| among those |
|
|
|
| displayed. |
|
|
|
|
|
|
33 | Reading program data | Read Program | Select the name of | Displayed only when there is |
| Reads the selected program data on the |
| the partition which | appropriate program data in the |
| RAM disk. |
| holds the program | RAM disk. |
|
|
| from among those |
|
|
|
| displayed. |
|
|
|
|
|
|
34 | Writing data | Write Data | OK | Displayed only when “On” is |
| If “OK” is selected here, the machine will |
|
| selected under the “RAM disk ON/ |
| enter a “waiting for data” state until data is |
|
| OFF” setting (item No.: 30). |
| sent from the host computer. To exit this |
|
|
|
| state, select the “GO” command in the |
|
|
|
| printer mode and then press the Enter key. |
|
|
|
|
|
|
|
|