Fujitsu MBB2073RC, MBB2147RC manual Write Write Extend

Page 43

3.3 Defect Management

(3)Automatic alternate block allocation

• Automatic alternate block allocation at read operation

If the ARRE flag in the MODE SELECT parameter permits the automatic alternate block allocation, the HDDs automatically execute the alternate block allocation and data duplication on the defective data block detected during the READ or READ EXTENDED command. This allocation method is the same as with the REASSIGN BLOCKS command (alternate sector treatment).

Automatic alternate block allocation at write operation

If AWRE flag in the MODE SELECT parameter permits the automatic alternate block allocation, the HDDs execute two kinds of automatic alternate processing during WRITE command processing as described below:

Type 1 (Reassignment of Uncorrectable Read Error sector)

1)Commands to be applied

-WRITE

-WRITE EXTEND

-WRITE at executing WRITE AND VERIFY

2)Application requirements

When any of the above commands is issued to LBA registered in the uncorrectable error log of the READ command (LBA log of uncorrectable error while the READ command is executed), the AWRE processing is applied.

3)AWRE processing

The following processings are performed when the LBA matches the one in the uncorrectable error log:

a)Primary media check

-Creates an uncorrectable error pattern (invalid LBA pattern) in the position of the error LBA, repeats the primary media check up to three times. If the error still occurs after the check repeated three times, it is judged to be defective. Then, it performs the alternate processing.

b)Alternate processing

-Alternate media check

Writes the data that causes an unrecoverable error into the alternate block, and performs the media check.

(If the alternate block is a defective sector, the block is registered to the G list, another alternate block is allocated.)

c)SA and defect map update processing (on alternate side)

When an error occurs in the alternate processing, this WRITE command terminates with error. When the alternate processing normally terminates, the WRITE command is executed.

C141-E257

39

Image 43
Contents MBB2147RC MBB2073RC Hard Disk Drives Product Manual For Safe Operation Revision Record Related Standards Overview of Manual PrefaceConventions for Alert Messages PrefaceImportant Alert Messages Important Alert ItemsData loss Important Alert ItemsSAS Interface Manual Manual Organization Product ManualThis page is intentionally left blank Contents Contents InstallationError Analysis Figures Tables This page is intentionally left blank Standard Features Standard Features Hardware Structure System ConfigurationGeneral Description Standard Features General Description Hardware Structure Sata style cable SAS Plug Connector Receptacle connector System Configuration This page is intentionally left blank Hardware Specifications Model name and order number Hardware SpecificationsModel names and order numbers 60/62 Meeprml SpecificationsFunction specifications MBB2147RC MBB2073RCSeek time ms Seek difference 4096 Cly/div Hardware SpecificationsEnvironmental/Power requirements Environmental specificationsReliability Error rateMtbf = Specifications Data Space Logical Data Block Addressing Defect Management Cylinder configurationData Space Data Format Data Space Spare area in cell Alternate spare areaTrack format Sector format Track skew/head skewData Space Format capacity Logical Data Block Addressing Alternate block allocation Defect Management Defect listDefect Management Alternate block allocation by Format Unit commandAlternate block allocation by Reassign Blocks command Write Write Extend Write Write Extended Format Unit Mounting Requirements Dimensions Installation RequirementsMounting orientations Installation RequirementsMounting frame structure example Mounting RequirementsVent hole location HDC Surface temperature check point and maximum temperatureMPU +5VDC MBB2147RC MBB2073RC Current waveform Max seek Power Supply RequirementsInterface connector CN1 power lines included Connection Requirements Interface connectorInterface connector SAS plug signal allocationCN1 Connector requirements Ready LED output signalRecommended connectors This page is intentionally left blank Installation Installation Setting Port Address SettingMounting HDDs Mounting procedures Installation Formatting Installation Setting parameters Arre Awre PER AwreArre Retry Count AT VerificationMaximum PRE-FETCH Ceiling Xffff Number of Cache Segments Disable PRE-FETCH Transfer Length Xffff Minimum PRE-FETCHDisc Maximum PRE-FETCHReady LED Meaning Self-diagnostic functions Diagnostics Self-diagnosticsDiagnostics and Maintenance Diagnostics Test programs Precautions MaintenanceMaintenance requirements Tools and test equipment Maintenance levelsTests Test flowchartOperation test Diagnostic testOperation Check Operation Check Initial seek operation checkTroubleshooting with HDD replacement in the field Troubleshooting Outline of troubleshooting proceduresSystem-level field troubleshooting TroubleshootingHDD troubleshooting Troubleshooting at the repair siteTroubleshooting with parts replacement in the factory TroubleshootingFinding possibly faulty parts Bag packaging Box packaging PackagingFraction packaging Sense Data Collection Sense data Sense Data Collection Sense Data AnalysisSense data format Sksv Error AnalysisILI LSBDefinition of sense data Sense Data AnalysisSense data 3-0C-03, 4-32-01, 4-40-xx, 4-C4-xx, Sense data 1-1x-xx, 3-1x-xx and E-1D-00 Disk read errorGlossary This page is intentionally left blank Acronyms and Abbreviations Acronyms and Abbreviations ECC BcrcPAD Mode SELECT/MODE SelectIndex Mtbf MttrIndex This page is intentionally left blank Comment Form This page is intentionally left blank