Fujitsu D5200 user manual FCC Class B Compliance Statement

Page 9

FCC Class B Compliance Statement

The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation.

NOTE:

This equipment has been tested and found to comply with the limits for a "Class B" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference- Causing Equipment Regulations. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Fujitsu is not responsible for any radio or television interference caused by unauthorised modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interference caused by such unauthorised modification, substitution or attachment will be the responsibility of the user.

The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC rules.

ix

D5200_0(INTRO)

9

12/7/06, 10:58 am

Image 9

Contents Declaration of Conformity Esprimo D5200 User’s ManualImportant Safety Instructions Class 1 Laser Products Before Reading this Manual Using this Product for High-Safety ApplicationsFor Safe Operation Backing Up the DataMicrosoft Service Pack Software License AgreementUse of the software Keep the accompanying CD-ROMs in a safe place Temperature and humidity conditionConventions Used in this Manual IntroductionNotational conventions Important Notes SafetyManufacturer’s notes Energy savingFCC Class B Compliance Statement Cleaning the PC Cleaning the system unit and the monitorTransporting the PC To institutional and corporate customers Disposal and recycling Disposal of the PC unitTo individual customers Disposal of the LCD unitXii Before Reading This Manual Organization of This ManualContents Unpacking and Checking the Delivery Steps for Initial SetupExternal devices Drives and boardsInstalling the Feet Setting Up the PCVertical positioning Horizontal positioning Point Connecting the mouse Connecting the keyboardConnecting standard keyboard Connect the Monitor, Mouse and KeyboardSwitching on monitor and PC Initial Switch-on Software will be InstalledConnecting External Devices Connecting cablesDisconnecting cables Connections on the system unit Connecting external devices to the parallel port Connecting external devices to the serial portSettings of the serial port Settings of the parallel portSwitching Off the PC Switching On the PCPower indicator Front Panels of the Main Unit of the Personal ComputerVent CD access indicator Disc access indicatorFloppy disk access indicator USB portsBack Panel of the Main Unit of the Personal Computer Mouse port Main switchKeyboard port Monitor portKeyboard Point Settings in Bios Setup Floppy DisksWorking with Floppy Disks Anti-theft Protection and Lead-sealing Check that the upper cover has been firmly installedInstalling New Software Mains voltage supply is faultyInternal power supply overloaded Screen stays blank Floppy Disk Cannot be Read or Written No Mouse Pointer Displayed on the ScreenWrong monitor has been set under Window XP Wrong RAM modules have been insertedRestoring the Hard Disk Contents Error Messages on the ScreenTime and/or Date is not Correct TipsInformation about Boards System ExpansionBefore Connecting Peripheral Devices PrecautionsInstall one peripheral device only at one time Taking precautions to static electricity Do not disassemble the power unitUse Acpi support peripheral devices Preparing screwdriversRemoving the Main Unit Cover How to remove the main unit coverInstalling Memory Locations for memory to be installed Memory to be installedTable of combinations of memory Installing memory D5200424-32 12/7/06, 1059 am Point Installing the Expansion Card Expansion cards to be installed Locations for expansion cards to be installedPress and raise the slot cover lock Remove the slot cover Installing expansion cardsInsert the expansion card into the port Install the installing fittingElectrical Data Point D5200533-39 12/7/06, 1100 am