Cisco Systems IE20004TSL, IE20004TSB, IE200016TCB manual Cisco IE-2000-4TS-L Front Panel View

Page 13

Chapter 1 Product Overview

Front Panel

Front Panel

This section describes the front panel components. See Table 1-1.

10/100BASE-T Ethernet ports

10/100/1000 uplink ports (available on some models).

Dual-purpose ports (available on some models).

SFP module slots (available on some models).

PoE/PoE+ ports (available on some models). See Power over Ethernet Ports, page 1-9.

RJ-45 console port

USB mini-Type B (console) port

LEDs

Power connectors

Alarm connector

Flash memory card slot

The following figures depict the components available on the various models in this product family. Not all models are illustrated.

Figure 1-1 Cisco IE-2000-4TS-L Front Panel View

3

1

±152-/24/48.

0.

0A

2

4TS

9

4

5

6

7

8

331547

 

1

10/100 Ethernet ports (downlink ports)

6

Power connector DC-B

 

 

 

 

 

 

 

2

SFP module slots (uplink ports)

7

Alarm connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco IE 2000 Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-25818-04

 

 

 

 

1-5

 

 

 

 

 

 

 

Image 13
Contents Americas Headquarters Cisco IE 2000 Switch Hardware Installation GuidePage N T E N T S Installation Guidelines Connecting to a Dual-Purpose Port Verifying Switch Operation IP Settings Purpose AudienceConventions Related Publications Product Overview Model Description Software Image Switch ModelsModel Description Software Image Model Description Software Image Cisco IE-2000-4TS-L Front Panel View Front PanelCisco IE-2000-8TC-L Front Panel Cisco IE-2000-16TC-L Front Panel View 10/100BASE-T Downlink Ports Cisco IE-2000-16PTC-G-E Switch Front Panel View10/100/1000BASE-T Uplink Ports 10/100BASE-T Uplink Ports100 Mb/s SFP Module Uplink Slots 100/1000 Mb/s SFP Module Uplink SlotsSFP Modules Dual-Purpose Gigabit Ethernet Uplink PortsType of SFP Module Model GLC-LH-SM Power ConnectorsPoE Power Connector Alarm ConnectorUSB Mini-Type B Port Management PortsLEDs LEDs on the Cisco IE 2000 SwitchSystem LED Express Setup LEDUSB-Mini Console LED Power Status LEDs Alarm LEDsPort Status LEDs Dual-Purpose Port LEDs Dual-Purpose Port LEDsPoE Status LED Flash Memory CardColor PoE Status 10 Flash Memory Card Slot Management Options Rear PanelNetwork Configurations Preparing for Installation Switch Installation140F 60C Statement Hazardous Area Installation Warnings 1080 North American Hazardous Location Approval Installation GuidelinesEnvironment and Enclosure Guidelines General Guidelines Verifying Package Contents Installing or Removing the Flash Memory Card OptionalInstalling the Flash Memory Card in the Switch RJ-45 Console Port USB Mini-Type B Console Port Connecting to a Console PortRJ-45 Console Port Connecting the Console CableRemoving the USB Mini-Type B Console Port Cover USB Mini-Type B Console PortChoose Start Control Panel Systems Supported Power Supplies Connecting to PowerTools and Equipment Dimensions Grounding the SwitchAttachable? UsageSlide the ground screw through the terminal Ground cable Preparing the AC Power Connection Connecting the Power Converter to an AC Power SourceConnecting AC Power Connecting the AC Power Source to the Power ConverterConnecting the Power Converter to a DC Power Source Wiring the DC Power Source Statement Label 12 Stripping the Power Connection Wire14 Inserting Wires in the Power Connector 15 Torquing the Power Connector Captive Screws 16 Completed DC Power Connections on the Power Connectors Attaching the Power Connectors to the Switch17 Attaching the Power Connectors to the Switch 18 Connecting the Power Connectors to the Switch Connecting Power to the Switch PoE DC-Input Optional 332021 Running Boot Fast Applying Power to the Power ConverterPowering On the Switch Verifying Boot Fast Installing the SwitchDisconnecting Power DIN Rail Switch Installing the Switch on a DIN RailRemoving the Switch from a DIN Rail Wiring the Protective Ground and DC Power for Alarm Circuits Connecting Alarm CircuitsLabel Connection Wiring the External Alarms21 Removing the Alarm Connector 332225 Attaching the Alarm Connector to the Switch 25 Connecting the Alarm Connector to the Switch Connecting Destination PortsConnecting to 10/100 and 10/100/1000 Ports 26 Connecting to an Ethernet Port Installing SFP Modules into SFP Module Slots Installing and Removing SFP ModulesRemoving SFP Modules from SFP Module Slots 28 Installing an SFP Module into an SFP Module SlotConnecting to SFP Modules LC connector Connecting to a Dual-Purpose Port Where to Go Next Verifying Switch OperationSwitch Installation Where to Go Next Switch Boot Fast Diagnosing ProblemsSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber-Optic Cables10/100 and 10/100/1000 Port Connections Interface SettingsSFP Module Ping End DeviceSpeed, Duplex, and Autonegotiation Switch PerformanceAutonegotiation and Network Interface Cards Cabling DistanceHow to Recover Passwords Resetting the SwitchSerial Number Location for the Cisco IE-2000 Switches Finding the Switch Serial NumberOperating Temperature Specifications Technical SpecificationsPower Requirements Technical SpecificationsEnvironmental Ranges Table A-2 Cisco IE 2000 Series Technical Specifications Physical Dimensions Table A-2 Cisco IE 2000 Series Technical Specifications Alarm Ratings Specification Alarm RatingsHazardous Locations Standards Hazardous Locations Standards10/100 Ports Connector SpecificationsDual-Purpose Ports SFP Module ConnectorsConsole Port Figure B-5 USB Type A-to-USB 5-Pin Mini-Type B Cable Alarm PortSFP Module Cables Cables and AdaptersCommercial SFPs Core Modal WavelengthBandwidth Type of SFP Module Nanometers Fiber Type MHz/km1 Cable Distance Extended temperature SFPsTP3 Cable PinoutsFigure B-9 Console Port Adapter PinoutsDSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceOL-25818-04 Removing the USB Mini-Type B Console Port Cover Accessing the CLI Through the Console PortFigure C-1 Removing the USB Mini-Type B Console Port Cover Figure C-2 Connecting the Console Cable Figure C-3 Connecting the USB-Mini Console Cable Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriverIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter an enable password, and press Return These choices appear