Cisco Systems IE200016TCB, IE20004TSB 10/100BASE-T Uplink Ports, 10/100/1000BASE-T Uplink Ports

Page 17

Chapter 1 Product Overview

Front Panel

You can use the mdix auto interface configuration command in the command-line interface (CLI) to enable the automatic medium-dependent interface crossover (auto-MDIX) feature. When the auto- MDIX feature is enabled, the switch detects the required cable type for copper Ethernet connections and configures the interfaces accordingly. For configuration information for this feature, see the switch software configuration guide or the switch command reference.

Power over Ethernet Ports

On certain models of the IE 2000 switch, four of the 10/100BASE-T ports are available as PoE ports. The four ports can operate as PoE (IEEE 802.3af) ports or can be configured to operate as PoE+

(IE 802.at) ports. Each PoE port requires 15.4 Watts of power while PoE+ requires 30 Watts. A 54VDC /1.2Amp power source (65W) can support 4 PoE ports or 2 PoE+ ports.

Cable lengths of up to 328 ft (100 m) are supported.

10/100BASE-T Uplink Ports

The IEEE 802.3u 10/100BASE-T uplink ports provide full-duplex 10, 100 Mb/s connectivity over Category 5 unshielded twisted pair (UTP) copper cabling. The default setting is autonegotiate. The cable can be up to 100 m (0.1 km) in length.

10/100/1000BASE-T Uplink Ports

The IEEE 802.3u 10/100/1000BASE-T uplink ports provide full-duplex 10, 100 or 1000 Mb/s connectivity over Category 5 unshielded twisted pair (UTP) copper cabling. The default setting is autonegotiate. The cable can be up to 100 m (0.1 km) in length.

100 Mb/s SFP Module Uplink Slots

The IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 Mb/s connectivity over multi-mode (MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic transceiver module that accepts a dual LC connector. Check the SFP specifications for the cable type and length.

100/1000 Mb/s SFP Module Uplink Slots

The IEEE 802.3u 100 Mb/s SFP module uplink slots provide full-duplex 100 or 1000 Mb/s connectivity over multi-mode (MM) fiber cables or single-mode (SM) fiber cables. These ports use a SFP fiber-optic transceiver module that accepts a dual LC connector. Check the SFP specifications for the cable type and length.

Dual-Purpose Fast Ethernet Uplink Ports

You can configure the dual-purpose Fast Ethernet uplink ports on the switch as either 10/100BASE-T ports or as 100 Mb/s SFP-module ports. You can set the 10/100 ports to autonegotiate, or you can configure them as fixed 10 or 100 Mb/s ports.

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

1-9

 

 

 

Image 17
Contents Americas Headquarters Cisco IE 2000 Switch Hardware Installation GuidePage N T E N T S Installation Guidelines Connecting to a Dual-Purpose Port Verifying Switch Operation IP Settings Conventions AudiencePurpose Related Publications Product Overview Model Description Software Image Switch ModelsModel Description Software Image Model Description Software Image Cisco IE-2000-4TS-L Front Panel View Front PanelCisco IE-2000-8TC-L Front Panel Cisco IE-2000-16TC-L Front Panel View 10/100BASE-T Downlink Ports Cisco IE-2000-16PTC-G-E Switch Front Panel View10/100/1000BASE-T Uplink Ports 10/100BASE-T Uplink Ports100 Mb/s SFP Module Uplink Slots 100/1000 Mb/s SFP Module Uplink SlotsType of SFP Module Model Dual-Purpose Gigabit Ethernet Uplink PortsSFP Modules GLC-LH-SM Power ConnectorsPoE Power Connector Alarm ConnectorUSB Mini-Type B Port Management PortsLEDs LEDs on the Cisco IE 2000 SwitchUSB-Mini Console LED Express Setup LEDSystem LED Power Status LEDs Alarm LEDsPort Status LEDs Dual-Purpose Port LEDs Dual-Purpose Port LEDsColor PoE Status Flash Memory CardPoE Status LED 10 Flash Memory Card Slot Management Options Rear PanelNetwork Configurations Preparing for Installation Switch Installation140F 60C Statement Hazardous Area Installation Warnings 1080 Environment and Enclosure Guidelines Installation GuidelinesNorth American Hazardous Location Approval General Guidelines Verifying Package Contents Installing or Removing the Flash Memory Card OptionalInstalling the Flash Memory Card in the Switch RJ-45 Console Port USB Mini-Type B Console Port Connecting to a Console PortRJ-45 Console Port Connecting the Console CableRemoving the USB Mini-Type B Console Port Cover USB Mini-Type B Console PortChoose Start Control Panel Systems Tools and Equipment Connecting to PowerSupported Power Supplies Dimensions Grounding the SwitchAttachable? UsageSlide the ground screw through the terminal Ground cable Preparing the AC Power Connection Connecting the Power Converter to an AC Power SourceConnecting AC Power Connecting the AC Power Source to the Power ConverterConnecting the Power Converter to a DC Power Source Wiring the DC Power Source Statement Label 12 Stripping the Power Connection Wire14 Inserting Wires in the Power Connector 15 Torquing the Power Connector Captive Screws 16 Completed DC Power Connections on the Power Connectors Attaching the Power Connectors to the Switch17 Attaching the Power Connectors to the Switch 18 Connecting the Power Connectors to the Switch Connecting Power to the Switch PoE DC-Input Optional 332021 Powering On the Switch Applying Power to the Power ConverterRunning Boot Fast Disconnecting Power Installing the SwitchVerifying Boot Fast DIN Rail Switch Installing the Switch on a DIN RailRemoving the Switch from a DIN Rail Wiring the Protective Ground and DC Power for Alarm Circuits Connecting Alarm CircuitsLabel Connection Wiring the External Alarms21 Removing the Alarm Connector 332225 Attaching the Alarm Connector to the Switch 25 Connecting the Alarm Connector to the Switch Connecting Destination PortsConnecting to 10/100 and 10/100/1000 Ports 26 Connecting to an Ethernet Port Installing SFP Modules into SFP Module Slots Installing and Removing SFP ModulesRemoving SFP Modules from SFP Module Slots 28 Installing an SFP Module into an SFP Module SlotConnecting to SFP Modules LC connector Connecting to a Dual-Purpose Port Where to Go Next Verifying Switch OperationSwitch Installation Where to Go Next Switch Boot Fast Diagnosing ProblemsSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber-Optic Cables10/100 and 10/100/1000 Port Connections Interface SettingsSFP Module Ping End DeviceSpeed, Duplex, and Autonegotiation Switch PerformanceAutonegotiation and Network Interface Cards Cabling DistanceHow to Recover Passwords Resetting the SwitchSerial Number Location for the Cisco IE-2000 Switches Finding the Switch Serial NumberOperating Temperature Specifications Technical SpecificationsEnvironmental Ranges Technical SpecificationsPower Requirements Table A-2 Cisco IE 2000 Series Technical Specifications Physical Dimensions Table A-2 Cisco IE 2000 Series Technical Specifications Alarm Ratings Specification Alarm RatingsHazardous Locations Standards Hazardous Locations Standards10/100 Ports Connector SpecificationsConsole Port SFP Module ConnectorsDual-Purpose Ports Figure B-5 USB Type A-to-USB 5-Pin Mini-Type B Cable Alarm PortSFP Module Cables Cables and AdaptersCommercial SFPs Core Modal WavelengthBandwidth Type of SFP Module Nanometers Fiber Type MHz/km1 Cable Distance Extended temperature SFPsTP3 Cable PinoutsFigure B-9 Console Port Adapter PinoutsDSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceOL-25818-04 Removing the USB Mini-Type B Console Port Cover Accessing the CLI Through the Console PortFigure C-1 Removing the USB Mini-Type B Console Port Cover Figure C-2 Connecting the Console Cable Figure C-3 Connecting the USB-Mini Console Cable Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriverCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return These choices appear