Cisco Systems IE200016TCB Installation Guidelines, North American Hazardous Location Approval

Page 35

Chapter 2 Switch Installation

Preparing for Installation

North American Hazardous Location Approval

The following information applies when operating this equipment in hazardous locations:

English: Products marked "Class I, Div 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code. When combining products within a system, the most adverse temperature code (lowest "T" number) may be used to help determine the overall temperature code of the system. Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation.

Français: Informations sur l'utilisation de cet équipement en environnements dangereux:

Les produits marqués "Class I, Div 2, GP A, B, C, D" ne conviennent qu'à une utilisation en environnements de Classe I Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livré avec des marquages sur sa plaque d'identification qui indiquent le code de température pour les environnements dangereux. Lorsque plusieurs produits sont combinés dans un système, le code de température le plus défavorable (code de température le plus faible) peut être utilisé pour déterminer le code de température global du système. Les combinaisons d'équipements dans le système sont sujettes à inspection par les autorités locales qualifiées au moment de l'installation.

EMC Environmental Conditions for Products Installed in the European Union

This section applies to products to be installed in the European Union.

The equipment is intended to operate under the following environmental conditions with respect to EMC:

•A separate defined location under the user’s control.

•Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.

•AC-power distribution shall be one of the following types, where applicable: TN-S and TN-C as defined in IEC 364-3.

In addition, if equipment is operated in a domestic environment, interference could occur.

Installation Guidelines

When determining where to place the switch, observe thee guidelines.

Environment and Enclosure Guidelines

Review these environmental and enclosure guidelines before installation:

•This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes up to 9842 ft (3 km) without derating.

Cisco IE 2000 Switch Hardware Installation Guide

 

OL-25818-04

2-5

 

 

 

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Americas Headquarters Cisco IE 2000 Switch Hardware Installation GuidePage N T E N T S Installation Guidelines Connecting to a Dual-Purpose Port Verifying Switch Operation IP Settings Conventions AudiencePurpose Related Publications Product Overview Model Description Software Image Switch ModelsModel Description Software Image Model Description Software Image Cisco IE-2000-4TS-L Front Panel View Front PanelCisco IE-2000-8TC-L Front Panel Cisco IE-2000-16TC-L Front Panel View 10/100BASE-T Downlink Ports Cisco IE-2000-16PTC-G-E Switch Front Panel View100/1000 Mb/s SFP Module Uplink Slots 10/100BASE-T Uplink Ports10/100/1000BASE-T Uplink Ports 100 Mb/s SFP Module Uplink SlotsType of SFP Module Model Dual-Purpose Gigabit Ethernet Uplink PortsSFP Modules GLC-LH-SM Power ConnectorsPoE Power Connector Alarm ConnectorUSB Mini-Type B Port Management PortsLEDs LEDs on the Cisco IE 2000 SwitchUSB-Mini Console LED Express Setup LEDSystem LED Power Status LEDs Alarm LEDsPort Status LEDs Dual-Purpose Port LEDs Dual-Purpose Port LEDsColor PoE Status Flash Memory CardPoE Status LED 10 Flash Memory Card Slot Management Options Rear PanelNetwork Configurations Preparing for Installation Switch Installation140F 60C Statement Hazardous Area Installation Warnings 1080 Environment and Enclosure Guidelines Installation GuidelinesNorth American Hazardous Location Approval General Guidelines Verifying Package Contents Installing or Removing the Flash Memory Card OptionalInstalling the Flash Memory Card in the Switch RJ-45 Console Port USB Mini-Type B Console Port Connecting to a Console PortRJ-45 Console Port Connecting the Console CableRemoving the USB Mini-Type B Console Port Cover USB Mini-Type B Console PortChoose Start Control Panel Systems Tools and Equipment Connecting to PowerSupported Power Supplies Usage Grounding the SwitchDimensions Attachable?Slide the ground screw through the terminal Ground cable Preparing the AC Power Connection Connecting the Power Converter to an AC Power SourceConnecting AC Power Connecting the AC Power Source to the Power ConverterConnecting the Power Converter to a DC Power Source Wiring the DC Power Source Statement Label 12 Stripping the Power Connection Wire14 Inserting Wires in the Power Connector 15 Torquing the Power Connector Captive Screws 16 Completed DC Power Connections on the Power Connectors Attaching the Power Connectors to the Switch17 Attaching the Power Connectors to the Switch 18 Connecting the Power Connectors to the Switch Connecting Power to the Switch PoE DC-Input Optional 332021 Powering On the Switch Applying Power to the Power ConverterRunning Boot Fast Disconnecting Power Installing the SwitchVerifying Boot Fast DIN Rail Switch Installing the Switch on a DIN RailRemoving the Switch from a DIN Rail Wiring the Protective Ground and DC Power for Alarm Circuits Connecting Alarm CircuitsLabel Connection Wiring the External Alarms21 Removing the Alarm Connector 332225 Attaching the Alarm Connector to the Switch 25 Connecting the Alarm Connector to the Switch Connecting Destination PortsConnecting to 10/100 and 10/100/1000 Ports 26 Connecting to an Ethernet Port Installing SFP Modules into SFP Module Slots Installing and Removing SFP ModulesRemoving SFP Modules from SFP Module Slots 28 Installing an SFP Module into an SFP Module SlotConnecting to SFP Modules LC connector Connecting to a Dual-Purpose Port Where to Go Next Verifying Switch OperationSwitch Installation Where to Go Next Switch Boot Fast Diagnosing ProblemsEthernet and Fiber-Optic Cables Switch LEDsSwitch Connections Bad or Damaged CablePing End Device Interface Settings10/100 and 10/100/1000 Port Connections SFP ModuleCabling Distance Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsHow to Recover Passwords Resetting the SwitchSerial Number Location for the Cisco IE-2000 Switches Finding the Switch Serial NumberOperating Temperature Specifications Technical SpecificationsEnvironmental Ranges Technical SpecificationsPower Requirements Table A-2 Cisco IE 2000 Series Technical Specifications Physical Dimensions Table A-2 Cisco IE 2000 Series Technical Specifications Hazardous Locations Standards Alarm RatingsAlarm Ratings Specification Hazardous Locations Standards10/100 Ports Connector SpecificationsConsole Port SFP Module ConnectorsDual-Purpose Ports Figure B-5 USB Type A-to-USB 5-Pin Mini-Type B Cable Alarm PortSFP Module Cables Cables and AdaptersCommercial SFPs Core Modal WavelengthBandwidth Type of SFP Module Nanometers Fiber Type MHz/km1 Cable Distance Extended temperature SFPsTP3 Cable PinoutsFigure B-9 Console Port Adapter PinoutsDSR DTR CTS RTS Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceOL-25818-04 Removing the USB Mini-Type B Console Port Cover Accessing the CLI Through the Console PortFigure C-1 Removing the USB Mini-Type B Console Port Cover Figure C-2 Connecting the Console Cable Figure C-3 Connecting the USB-Mini Console Cable Installing the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriverCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return These choices appear
Top Page Image Contents