Cisco Systems SFS 3012R manual OL-11187-01

Page 34

Chapter 2 Installing and Booting the Cisco SFS 3012R Server Switch

Safety

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Statement 1043

Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation. Install only in accordance with national and local wiring regulations. Statement 1045

Warning Use of controls, adjustments, or performing procedures other than those specified may result in hazardous radiation exposure. Statement 1057

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

2-2	OL-11187-01

Image 34

Contents Corporate Headquarters Text Part Number OL-11187-01Page N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Organization AudienceChapter Title Description Conventions Convention DescriptionStatement 1071-Warning Definition Bewaar Deze InstructiesAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Related Documentation XivCisco.com Obtaining DocumentationProduct Documentation DVD Ordering Documentation Documentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information XixPreface Obtaining Additional Publications and Information Cisco SFS 3012R Server Switch Overview IntroductionUnified Fabric FeaturesPerformance Transparent TopologyScalability Fully Redundant System ArchitectureCisco SFS 3012R Server Switch Chassis 6 8 10 12Cisco SFS 3012R Server Switch Components Controller ModulesCisco SFS 3012R Server Switch Controller Module Ethernet and Fibre Channel Gateways Ethernet ports Ethernet gateway status LEDs Ejector handleFibre Channel Gateway Expansion Module InfiniBand Switch Modules InfiniBand Switch ModulePower Supply Modules Power Supply ModuleBlower Modules Blower ModuleOL-11187-01 Installing and Booting the Cisco SFS 3012R Server Switch SafetyOL-11187-01 Preparing for Installation Installing Cisco SFS 3012R Server Switch ComponentsMounting the Cisco SFS 3012R Server Switch on a Rack Mounting bracket Shelf railAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Assigning a Static IP Address Obtaining an IP Address with DhcpConnecting InfiniBand Hosts Following exampleInfiniBand Cable with Pinch Connector Managing the Cisco SFS 3012R Server Switch Removing a Pinch ConnectorA P T E R Installing a Controller Module Inserting the Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Removing an InfiniBand Switch Module Installing a Power Supply Module180762 Removing a Power Supply Module Installing a Blower ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing and Updating the Software Image Viewing the Software Image VersionViewing the Software Image Version with the CLI SFS-3012R#show card-inventoryViewing the Software Image Version of the Controller Module Updating the Software Image Viewing Current Image of an Individual ModuleUpdating the Software Image with the CLI This example shows the copy operationUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting a Software Image Deleting an Image with the CLISelect Maintenance File Management Deleting an Image with the Element Manager GUICisco SFS 3012R Server Switch LEDs Cisco SFS 3012R Server Switch System Status LED LED State IndicationPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsController LED States Indication Controller LEDsBlower LED States Indication Power LED States Indication Location of Management Ethernet Port LEDsInfiniBand LEDs InfiniBand Switch Module LEDsLED States Indication InfiniBand Port LEDs Fibre Channel LEDs Fibre Channel Gateway LEDsFibre Channel Port LEDs Off Gbps Solid greenEthernet Gateway LEDs Location of Ethernet Gateway and Ethernet Port LEDsEthernet Gateway LEDs Ethernet Port LEDsGeneral Specifications Specification DetailLaser Specifications Electrical SpecificationsCertifications/Regulatory D E IN-2 IN-3 IN-4