Cisco Systems SFS 3012R manual A P T E R

Page 45

C H A P T E R 3

Installing and Removing Server Switch Field Replaceable Units (FRUs)

This chapter provides step-by-step instructions for performing the following procedures:

•Installing a Controller Module, page 3-2

•Adding or Replacing Ethernet or Fibre Channel Gateways, page 3-3

•Installing an InfiniBand Switch Module, page 3-4

•Removing an InfiniBand Switch Module, page 3-7

•Installing a Power Supply Module, page 3-7

•Removing a Power Supply Module, page 3-9

•Installing a Blower Module, page 3-9

•Removing a Blower Module, page 3-11

The components of the Cisco SFS 3012R Server Switch support the scalability and high availability of the server switch. The sections in this chapter discuss how to use, install, remove, and swap FRUs to maximize the potential of your Cisco SFS 3012R Server Switch.

You can install the following components in your chassis:

•Controller modules

•I/O gateways (Fibre Channel and Ethernet)

•InfiniBand switch modules

•Power supplies

•Blower modules

Caution Never place your hand inside an empty card or module bay. You should never have cause to place a hand anywhere inside the Cisco SFS 3012R Server Switch chassis. Unused module bays should always have a Cisco SFS 3012R Server Switch blanking panel over the bay to ensure proper safety, ventilation, and cooling.

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

	OL-11187-01	3-1

Image 45

Contents Text Part Number OL-11187-01 Corporate HeadquartersPage N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Audience OrganizationChapter Title Description Convention Description ConventionsBewaar Deze Instructies Statement 1071-Warning DefinitionWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Xiv Related DocumentationObtaining Documentation Cisco.comProduct Documentation DVD Ordering Documentation Reporting Security Problems in Cisco Products Documentation FeedbackCisco Product Security Overview Product Alerts and Field Notices Obtaining Technical AssistanceCisco Technical Support & Documentation Website Definitions of Service Request Severity Submitting a Service RequestXix Obtaining Additional Publications and InformationPreface Obtaining Additional Publications and Information Introduction Cisco SFS 3012R Server Switch OverviewPerformance FeaturesUnified Fabric Transparent TopologyFully Redundant System Architecture Scalability6 8 10 12 Cisco SFS 3012R Server Switch ChassisController Modules Cisco SFS 3012R Server Switch ComponentsCisco SFS 3012R Server Switch Controller Module Ethernet ports Ethernet gateway status LEDs Ejector handle Ethernet and Fibre Channel GatewaysFibre Channel Gateway Expansion Module InfiniBand Switch Module InfiniBand Switch ModulesPower Supply Module Power Supply ModulesBlower Module Blower ModulesOL-11187-01 Safety Installing and Booting the Cisco SFS 3012R Server SwitchOL-11187-01 Installing Cisco SFS 3012R Server Switch Components Preparing for InstallationMounting bracket Shelf rail Mounting the Cisco SFS 3012R Server Switch on a RackAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Obtaining an IP Address with Dhcp Assigning a Static IP AddressFollowing example Connecting InfiniBand HostsInfiniBand Cable with Pinch Connector Removing a Pinch Connector Managing the Cisco SFS 3012R Server SwitchA P T E R Inserting the Controller Module Installing a Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Installing a Power Supply Module Removing an InfiniBand Switch Module180762 Installing a Blower Module Removing a Power Supply ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing the Software Image Version Viewing and Updating the Software ImageSFS-3012R#show card-inventory Viewing the Software Image Version with the CLIViewing the Software Image Version of the Controller Module Viewing Current Image of an Individual Module Updating the Software ImageThis example shows the copy operation Updating the Software Image with the CLIUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting an Image with the CLI Deleting a Software ImageDeleting an Image with the Element Manager GUI Select Maintenance File ManagementCisco SFS 3012R Server Switch LEDs LED State Indication Cisco SFS 3012R Server Switch System Status LEDPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsController LEDs Controller LED States IndicationBlower LED States Indication Location of Management Ethernet Port LEDs Power LED States IndicationInfiniBand Switch Module LEDs InfiniBand LEDsLED States Indication InfiniBand Port LEDs Fibre Channel Gateway LEDs Fibre Channel LEDsOff Gbps Solid green Fibre Channel Port LEDsLocation of Ethernet Gateway and Ethernet Port LEDs Ethernet Gateway LEDsEthernet Port LEDs Ethernet Gateway LEDsSpecification Detail General SpecificationsElectrical Specifications Laser SpecificationsCertifications/Regulatory D E IN-2 IN-3 IN-4