Cisco Systems SFS 3012R manual Attaching the Shelf to the Rack

Page 37

Chapter 2 Installing and Booting the Cisco SFS 3012R Server Switch

Mounting the Cisco SFS 3012R Server Switch on a Rack

Step 3 Attach the shelf rails to either side of the Cisco SFS 3012R Server Switch chassis as follows:

a.Unpack the shelf assembly kit (ordered and shipped separately).

b.Identify the shelf rails labeled TS360/SFS 3012.

c.Attach the rails to the chassis with the four screws provided, as shown in Figure 2-1.

Step 4 Mount the shelf onto the rack, as shown in Figure 2-2, using the procedure outlined below. (For additional details about the shelf installation procedure, see “Install the Shelf Kit” in the Cisco SFS 7008 InfiniBand and Cisco 3012 Multifabric Server Switches Optional Shelf Kit, Contents and Installation Guide, which ships with the shelf assembly.)

a.Unpack the shelf assembly, and remove the extension brackets.

b.Verify that the shelf position provides sufficient clearance for the Cisco SFS 3012R Server Switch and all cables.

c.Use four screws that fit your rack (not included) to attach the extension brackets to the rack posts at the rack end at which the bezel end of the chassis will sit. Each bracket must wrap around the inside of the rack post and attach by its flange to the side of the rack post that faces away from the rack.

d.Slide the shelf onto the installed extension brackets until the shelf flange makes contact with the rack posts at the rack end at which the cable end of the chassis will sit.

Figure 2-2 Attaching the Shelf to the Rack

180734

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

 

OL-11187-01

2-5

 

 

 

Image 37
Contents Text Part Number OL-11187-01 Corporate HeadquartersPage N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Organization AudienceChapter Title Description Convention Description ConventionsBewaar Deze Instructies Statement 1071-Warning DefinitionAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Xiv Related DocumentationCisco.com Obtaining DocumentationProduct Documentation DVD Ordering Documentation Documentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Definitions of Service Request Severity Submitting a Service RequestXix Obtaining Additional Publications and InformationPreface Obtaining Additional Publications and Information Introduction Cisco SFS 3012R Server Switch OverviewPerformance FeaturesUnified Fabric Transparent TopologyFully Redundant System Architecture Scalability6 8 10 12 Cisco SFS 3012R Server Switch ChassisController Modules Cisco SFS 3012R Server Switch ComponentsCisco SFS 3012R Server Switch Controller Module Ethernet ports Ethernet gateway status LEDs Ejector handle Ethernet and Fibre Channel GatewaysFibre Channel Gateway Expansion Module InfiniBand Switch Module InfiniBand Switch ModulesPower Supply Module Power Supply ModulesBlower Module Blower ModulesOL-11187-01 Safety Installing and Booting the Cisco SFS 3012R Server SwitchOL-11187-01 Installing Cisco SFS 3012R Server Switch Components Preparing for InstallationMounting bracket Shelf rail Mounting the Cisco SFS 3012R Server Switch on a RackAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Obtaining an IP Address with Dhcp Assigning a Static IP AddressFollowing example Connecting InfiniBand HostsInfiniBand Cable with Pinch Connector Removing a Pinch Connector Managing the Cisco SFS 3012R Server SwitchA P T E R Inserting the Controller Module Installing a Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Installing a Power Supply Module Removing an InfiniBand Switch Module180762 Installing a Blower Module Removing a Power Supply ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing the Software Image Version Viewing and Updating the Software ImageSFS-3012R#show card-inventory Viewing the Software Image Version with the CLIViewing the Software Image Version of the Controller Module Viewing Current Image of an Individual Module Updating the Software ImageThis example shows the copy operation Updating the Software Image with the CLIUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting an Image with the CLI Deleting a Software ImageDeleting an Image with the Element Manager GUI Select Maintenance File ManagementCisco SFS 3012R Server Switch LEDs LED State Indication Cisco SFS 3012R Server Switch System Status LEDPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsController LED States Indication Controller LEDsBlower LED States Indication Location of Management Ethernet Port LEDs Power LED States IndicationInfiniBand LEDs InfiniBand Switch Module LEDsLED States Indication InfiniBand Port LEDs Fibre Channel Gateway LEDs Fibre Channel LEDsOff Gbps Solid green Fibre Channel Port LEDsLocation of Ethernet Gateway and Ethernet Port LEDs Ethernet Gateway LEDsEthernet Port LEDs Ethernet Gateway LEDsSpecification Detail General SpecificationsLaser Specifications Electrical SpecificationsCertifications/Regulatory D E IN-2 IN-3 IN-4