Cisco Systems SFS 3012R manual Adding or Replacing Ethernet or Fibre Channel Gateways

Page 47

Chapter 3 Installing and Removing Server Switch Field Replaceable Units (FRUs)

Adding or Replacing Ethernet or Fibre Channel Gateways

Step 7 Push the ejector lever up until it clicks into place, as shown in Figure 3-2.

Figure 3-2 Closing the Ejector Lever

180743

Adding or Replacing Ethernet or Fibre Channel Gateways

You can add, remove, and swap I/O gateways while your Cisco SFS 3012R Server Switch runs. However, if the software image on your gateway does not match the software image that runs on your server switch, you must install the correct software on your gateway. For details, refer to the install command in the Cisco SFS 7000 Series Product Family Command Reference.

Chapter 4, “Viewing and Updating the Software Image” provides instructions for viewing and updating the software image. To update a single gateway, use the standard installation procedure, but do not reboot the chassis. You can simply enable and disable the individual gateway to activate the new software image.

To install a gateway, perform the following steps:

Step 1 Ground yourself using an approved ground wrist strap.

Step 2 Remove the blanking panel if one resides in the slot.

Step 3 Remove the gateway module from any packaging.

Step 4 Extend the ejector lever on the gateway completely.

Step 5 Insert the gateway into an expansion module slot such that the ejector lever sits on the bottom-left-hand side of the module.

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

 

OL-11187-01

3-3

 

 

 

Image 47
Contents Text Part Number OL-11187-01 Corporate HeadquartersPage N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Chapter Title Description AudienceOrganization Convention Description ConventionsBewaar Deze Instructies Statement 1071-Warning DefinitionAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Xiv Related DocumentationProduct Documentation DVD Ordering Documentation Obtaining DocumentationCisco.com Cisco Product Security Overview Reporting Security Problems in Cisco ProductsDocumentation Feedback Cisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Definitions of Service Request Severity Submitting a Service RequestXix Obtaining Additional Publications and InformationPreface Obtaining Additional Publications and Information Introduction Cisco SFS 3012R Server Switch OverviewTransparent Topology FeaturesPerformance Unified FabricFully Redundant System Architecture Scalability6 8 10 12 Cisco SFS 3012R Server Switch ChassisController Modules Cisco SFS 3012R Server Switch ComponentsCisco SFS 3012R Server Switch Controller Module Ethernet ports Ethernet gateway status LEDs Ejector handle Ethernet and Fibre Channel GatewaysFibre Channel Gateway Expansion Module InfiniBand Switch Module InfiniBand Switch ModulesPower Supply Module Power Supply ModulesBlower Module Blower ModulesOL-11187-01 Safety Installing and Booting the Cisco SFS 3012R Server SwitchOL-11187-01 Installing Cisco SFS 3012R Server Switch Components Preparing for InstallationMounting bracket Shelf rail Mounting the Cisco SFS 3012R Server Switch on a RackAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Obtaining an IP Address with Dhcp Assigning a Static IP AddressFollowing example Connecting InfiniBand HostsInfiniBand Cable with Pinch Connector Removing a Pinch Connector Managing the Cisco SFS 3012R Server SwitchA P T E R Inserting the Controller Module Installing a Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Installing a Power Supply Module Removing an InfiniBand Switch Module180762 Installing a Blower Module Removing a Power Supply ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing the Software Image Version Viewing and Updating the Software ImageSFS-3012R#show card-inventory Viewing the Software Image Version with the CLIViewing the Software Image Version of the Controller Module Viewing Current Image of an Individual Module Updating the Software ImageThis example shows the copy operation Updating the Software Image with the CLIUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting an Image with the CLI Deleting a Software ImageDeleting an Image with the Element Manager GUI Select Maintenance File ManagementCisco SFS 3012R Server Switch LEDs LED State Indication Cisco SFS 3012R Server Switch System Status LEDPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsBlower LED States Indication Controller LEDsController LED States Indication Location of Management Ethernet Port LEDs Power LED States IndicationLED States Indication InfiniBand Switch Module LEDsInfiniBand LEDs InfiniBand Port LEDs Fibre Channel Gateway LEDs Fibre Channel LEDsOff Gbps Solid green Fibre Channel Port LEDsLocation of Ethernet Gateway and Ethernet Port LEDs Ethernet Gateway LEDsEthernet Port LEDs Ethernet Gateway LEDsSpecification Detail General SpecificationsCertifications/Regulatory Electrical SpecificationsLaser Specifications D E IN-2 IN-3 IN-4