Cisco Systems SFS 3012R manual Securing an InfiniBand Switch Module

Page 50

Chapter 3 Installing and Removing Server Switch Field Replaceable Units (FRUs)

Installing an InfiniBand Switch Module

Step 8 Tighten the screws on either side of the switch module to secure it to the chassis.

Figure 3-5 Securing an InfiniBand Switch Module

180744

Step 9 Verify that the system image on the InfiniBand switch module is consistent with the image on other cards in the chassis and update the image, if necessary. Use the show card command to determine the current image, as shown in the following example:

SFS-3012R#show card all

================================================================================

Card Information

================================================================================

admin

oper

admin

oper

oper

slot type

type

status

status

code

--------------------------------------------------------------------------------

1*

controller

controller

up

up

normal

7

fc2port2G

fc2port2G

up

up

normal

8

fc2port2G

fc2port2G

up

up

normal

14

controller

controller

up

up

standby

15

ib12port4x

ib12port4x

up

down

wrong-image

16

ib12port4x

ib12port4x

up

up

normal

================================================================================

Card Boot Information

================================================================================Pr

boot

boot

boot

slot stage

status

image

--------------------------------------------------------------------------------

1

done

success

TopspinOS-2.8.0/build068

7

done

success

TopspinOS-2.8.0/build068

8

done

success

TopspinOS-2.8.0/build068

14

done

success

TopspinOS-2.8.0/build068

15

none

none

TopspinOS-2.8.0/build060

16

done

success

TopspinOS-2.8.0/build068

SFS-3012R#

To interpret the output, examine the information for the slot in which you just installed the InfiniBand switch module. If the oper status is shown as “down” and the oper-code as “wrong-image” (as shown for slot 15 in the example), then the module needs to have its image updated.

See Chapter 4, “Viewing and Updating the Software Image” for instructions about updating the software image on the InfiniBand switch module.

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

3-6

OL-11187-01

 

 

Image 50
Contents Corporate Headquarters Text Part Number OL-11187-01Page N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Chapter Title Description AudienceOrganization Conventions Convention DescriptionStatement 1071-Warning Definition Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Related Documentation XivProduct Documentation DVD Ordering Documentation Obtaining DocumentationCisco.com Cisco Product Security Overview Reporting Security Problems in Cisco ProductsDocumentation Feedback Cisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information XixPreface Obtaining Additional Publications and Information Cisco SFS 3012R Server Switch Overview IntroductionUnified Fabric FeaturesPerformance Transparent TopologyScalability Fully Redundant System ArchitectureCisco SFS 3012R Server Switch Chassis 6 8 10 12Cisco SFS 3012R Server Switch Components Controller ModulesCisco SFS 3012R Server Switch Controller Module Ethernet and Fibre Channel Gateways Ethernet ports Ethernet gateway status LEDs Ejector handleFibre Channel Gateway Expansion Module InfiniBand Switch Modules InfiniBand Switch ModulePower Supply Modules Power Supply ModuleBlower Modules Blower ModuleOL-11187-01 Installing and Booting the Cisco SFS 3012R Server Switch SafetyOL-11187-01 Preparing for Installation Installing Cisco SFS 3012R Server Switch ComponentsMounting the Cisco SFS 3012R Server Switch on a Rack Mounting bracket Shelf railAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Assigning a Static IP Address Obtaining an IP Address with DhcpConnecting InfiniBand Hosts Following exampleInfiniBand Cable with Pinch Connector Managing the Cisco SFS 3012R Server Switch Removing a Pinch ConnectorA P T E R Installing a Controller Module Inserting the Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Removing an InfiniBand Switch Module Installing a Power Supply Module180762 Removing a Power Supply Module Installing a Blower ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing and Updating the Software Image Viewing the Software Image VersionViewing the Software Image Version with the CLI SFS-3012R#show card-inventoryViewing the Software Image Version of the Controller Module Updating the Software Image Viewing Current Image of an Individual ModuleUpdating the Software Image with the CLI This example shows the copy operationUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting a Software Image Deleting an Image with the CLISelect Maintenance File Management Deleting an Image with the Element Manager GUICisco SFS 3012R Server Switch LEDs Cisco SFS 3012R Server Switch System Status LED LED State IndicationPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsBlower LED States Indication Controller LEDsController LED States Indication Power LED States Indication Location of Management Ethernet Port LEDsLED States Indication InfiniBand Switch Module LEDsInfiniBand LEDs InfiniBand Port LEDs Fibre Channel LEDs Fibre Channel Gateway LEDsFibre Channel Port LEDs Off Gbps Solid greenEthernet Gateway LEDs Location of Ethernet Gateway and Ethernet Port LEDsEthernet Gateway LEDs Ethernet Port LEDsGeneral Specifications Specification DetailCertifications/Regulatory Electrical SpecificationsLaser Specifications D E IN-2 IN-3 IN-4