Cisco Systems SFS 3012R manual Viewing the Software Image Version with the CLI

Page 58

Chapter 4 Viewing and Updating the Software Image

Viewing the Software Image Version

Viewing the Software Image Version with the CLI

Use the CLI to view software versions on the chassis as follows:

Step 1 To view the primary software image version for all cards in the chassis, use the show card-inventorycommand, as shown in the following example:

SFS-3012R#show card-inventory

================================================================================

Card Resource/Inventory Information

================================================================================

slot-id : 1 used-memory : 77040 (kbytes) free-memory : 50272 (kbytes)

used-disk-space : 45048 (kbytes)

free-disk-space : 57331 (kbytes) last-image-source : TopspinOS-2.0.0/build495

primary-image-source :TopspinOS-2.0.0/build495image : TopspinOS-2.0.0/build495

cpu-descr : PPC 440GP Rev. C - Rev 4.129 (pvr 4012 0481) fpga-firmware-rev : 6

ib-firmware-rev : 200000000

slot-id : 10 used-memory : 47676 (kbytes) free-memory : 34948 (kbytes)

used-disk-space : 8909 (kbytes)

free-disk-space : 33361 (kbytes) last-image-source : TopspinOS-2.0.0/build495

primary-image-source : TopspinOS-2.0.0/build495 image : TopspinOS-2.0.0/build495

<output truncated>

Interpret the display as follows:

a.Look for the primary-image-sourcefield for each slot. The slots are identified in Figure 1-3 on page 1-4.

b.Determine whether or not any slot has a software image version (primary-image-source) that is older then the others. This slot will need its image updated.

c.Compare your most recent image with the most recent image available. Check the Cisco.com site or your ftp site for details about image availability. Consider updating to the newer image, if available.

d.If you need to download a new image, note the amount of memory and disk space available. Check also the file size of the new image that you will download from the Cisco.com website or from the ftp site and determine whether or not you need to create space.

e.Examine the files listed in the image field of the display. Any file listed in the image field that is neither the last-image-source nor the primary-image-source is a candidate for deletion.

 

 

 

Step 2

Use the dir image command to view all existing boot images on the chassis, and determine whether or

 

 

 

 

not they are currently installed, as shown in the following example:

 

 

 

 

SFS-3012R> enable

 

 

 

 

SFS-3012R# dir image

 

 

 

 

=============================================================================

 

 

 

 

 

Existing Boot-Images on System

 

 

 

 

=============================================================================

 

 

 

 

 

slot date-created size file-name

 

 

 

 

--------------------------------------------------------------------------------

 

 

 

 

 

1 Tue Nov 25 18:46:32 2003 30695264 Topspin360-TopspinOS-2.0.0-build212.img

 

 

 

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

 

 

 

 

4-2

 

 

OL-11187-01

 

 

 

 

 

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Corporate Headquarters Text Part Number OL-11187-01Page N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Organization AudienceChapter Title Description Conventions Convention DescriptionStatement 1071-Warning Definition Bewaar Deze InstructiesAvvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige SicherheitshinweiseAviso Instruções Importantes DE Segurança Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Related Documentation XivCisco.com Obtaining DocumentationProduct Documentation DVD Ordering Documentation Documentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Product Alerts and Field NoticesCisco Technical Support & Documentation Website Submitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information XixPreface Obtaining Additional Publications and Information Cisco SFS 3012R Server Switch Overview IntroductionUnified Fabric FeaturesPerformance Transparent TopologyScalability Fully Redundant System ArchitectureCisco SFS 3012R Server Switch Chassis 6 8 10 12Cisco SFS 3012R Server Switch Components Controller ModulesCisco SFS 3012R Server Switch Controller Module Ethernet and Fibre Channel Gateways Ethernet ports Ethernet gateway status LEDs Ejector handleFibre Channel Gateway Expansion Module InfiniBand Switch Modules InfiniBand Switch ModulePower Supply Modules Power Supply ModuleBlower Modules Blower ModuleOL-11187-01 Installing and Booting the Cisco SFS 3012R Server Switch SafetyOL-11187-01 Preparing for Installation Installing Cisco SFS 3012R Server Switch ComponentsMounting the Cisco SFS 3012R Server Switch on a Rack Mounting bracket Shelf railAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Assigning a Static IP Address Obtaining an IP Address with DhcpConnecting InfiniBand Hosts Following exampleInfiniBand Cable with Pinch Connector Managing the Cisco SFS 3012R Server Switch Removing a Pinch ConnectorA P T E R Installing a Controller Module Inserting the Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Removing an InfiniBand Switch Module Installing a Power Supply Module180762 Removing a Power Supply Module Installing a Blower ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing and Updating the Software Image Viewing the Software Image VersionViewing the Software Image Version with the CLI SFS-3012R#show card-inventoryViewing the Software Image Version of the Controller Module Updating the Software Image Viewing Current Image of an Individual ModuleUpdating the Software Image with the CLI This example shows the copy operationUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting a Software Image Deleting an Image with the CLISelect Maintenance File Management Deleting an Image with the Element Manager GUICisco SFS 3012R Server Switch LEDs Cisco SFS 3012R Server Switch System Status LED LED State IndicationPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsController LED States Indication Controller LEDsBlower LED States Indication Power LED States Indication Location of Management Ethernet Port LEDsInfiniBand LEDs InfiniBand Switch Module LEDsLED States Indication InfiniBand Port LEDs Fibre Channel LEDs Fibre Channel Gateway LEDsFibre Channel Port LEDs Off Gbps Solid greenEthernet Gateway LEDs Location of Ethernet Gateway and Ethernet Port LEDsEthernet Gateway LEDs Ethernet Port LEDsGeneral Specifications Specification DetailLaser Specifications Electrical SpecificationsCertifications/Regulatory D E IN-2 IN-3 IN-4
Top Page Image Contents