Cisco Systems SFS 3012R manual Preparing for Installation

Page 35

Chapter 2 Installing and Booting the Cisco SFS 3012R Server Switch

Preparing for Installation

Preparing for Installation

Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with both hands. To prevent injury, keep your back straight and lift with your legs, not your back. To prevent damage to the chassis and components, never attempt to lift the chassis with the handles on the power supplies or on the interface processors, or by the plastic panels on the front of the chassis. These handles were not designed to support the weight of the chassis. Statement 5

Prepare for your installation by unpacking the product, and ensuring other necessary components are available, as described in the following steps.

Step 1 Remove all components from the Cisco SFS 3012R Server Switch shipping container, and identify them. Step 2 Place the chassis on a secure, clean surface.

Step 3 Verify that you have a Cisco SFS 7008 InfiniBand and Cisco SFS 3012 Multifabric Server Switches Shelf Kit at hand (ordered and shipped separately, product number SFS-7008P-RKIT).

Step 4 Verify that you have at hand all Ethernet gateways and Fibre Channel gateways that you will need to increase the port count of your Cisco SFS 3012R Server Switch.

Step 5 Prepare a management workstation (not included), such as a PC running terminal-emulation software (not included), and a straight-through M/F DB-9 serial cable (included).

Installing Cisco SFS 3012R Server Switch Components

We recommend that you install all Ethernet or Fibre Channel gateway modules before you mount the Cisco SFS 3012R Server Switch, as described in the “Adding or Replacing Ethernet or Fibre Channel Gateways” section on page 3-3. These components are not preinstalled in the Cisco SFS 3012R Server Switch chassis. However, you can add or change modules after mounting the Cisco SFS 3012R Server Switch chassis in the rack. For details about installing Fibre Channel gateways, see the Cisco SFS 3000 Series Product Family Fibre Channel Gateway User Guide. For details about installing Ethernet gateways, see the Cisco SFS 3000 Series Product Family Ethernet Gateway User Guide.

Note All cable connections to Ethernet gateways must use shielded RJ45 CAT5 Ethernet cables.

All other server switch modules are preinstalled in your Cisco SFS 3012R Server Switch before shipping. You can, if needed, still add or replace these components before mounting the Cisco SFS 3012R Server Switch chassis. These components include the following:

•Switch modules

•Controller modules

•Power supplies

•Blower modules

Instructions for installing or replacing these components appear in Chapter 3, “Installing and Removing Server Switch Field Replaceable Units (FRUs)”.

Cisco SFS 3012R Multifabric Server Switch Hardware Installation Guide

 

OL-11187-01

2-3

 

 

 

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Text Part Number OL-11187-01 Corporate HeadquartersPage N T E N T S Blower Modules Cisco SFS 3012R Server Switch LEDs OL-11187-01 Chapter Title Description AudienceOrganization Convention Description ConventionsBewaar Deze Instructies Statement 1071-Warning DefinitionAviso Instruções Importantes DE Segurança Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Guarde Estas Instrucciones GEM Disse Anvisninger Xiii Xiv Related DocumentationProduct Documentation DVD Ordering Documentation Obtaining DocumentationCisco.com Cisco Product Security Overview Reporting Security Problems in Cisco ProductsDocumentation Feedback Cisco Technical Support & Documentation Website Product Alerts and Field NoticesObtaining Technical Assistance Definitions of Service Request Severity Submitting a Service RequestXix Obtaining Additional Publications and InformationPreface Obtaining Additional Publications and Information Introduction Cisco SFS 3012R Server Switch OverviewTransparent Topology FeaturesPerformance Unified FabricFully Redundant System Architecture Scalability6 8 10 12 Cisco SFS 3012R Server Switch ChassisController Modules Cisco SFS 3012R Server Switch ComponentsCisco SFS 3012R Server Switch Controller Module Ethernet ports Ethernet gateway status LEDs Ejector handle Ethernet and Fibre Channel GatewaysFibre Channel Gateway Expansion Module InfiniBand Switch Module InfiniBand Switch ModulesPower Supply Module Power Supply ModulesBlower Module Blower ModulesOL-11187-01 Safety Installing and Booting the Cisco SFS 3012R Server SwitchOL-11187-01 Installing Cisco SFS 3012R Server Switch Components Preparing for InstallationMounting bracket Shelf rail Mounting the Cisco SFS 3012R Server Switch on a RackAttaching the Shelf to the Rack Positioning and Sliding the Chassis onto the Shelf Firmly tighten the shelf screws at the cable end Attaching a Serial Console Cable to a PC or Terminal Obtaining an IP Address with Dhcp Assigning a Static IP AddressFollowing example Connecting InfiniBand HostsInfiniBand Cable with Pinch Connector Removing a Pinch Connector Managing the Cisco SFS 3012R Server SwitchA P T E R Inserting the Controller Module Installing a Controller ModuleAdding or Replacing Ethernet or Fibre Channel Gateways Installing an InfiniBand Switch Module Close both fastener levers simultaneously and completely Securing an InfiniBand Switch Module Installing a Power Supply Module Removing an InfiniBand Switch Module180762 Installing a Blower Module Removing a Power Supply ModuleInserting a Power Supply Removing a Blower Module OL-11187-01 Viewing the Software Image Version Viewing and Updating the Software ImageSFS-3012R#show card-inventory Viewing the Software Image Version with the CLIViewing the Software Image Version of the Controller Module Viewing Current Image of an Individual Module Updating the Software ImageThis example shows the copy operation Updating the Software Image with the CLIUpdating the Software Image with the Element Manager GUI Click the Import button Import File window appears Select Maintenance-Reboot Deleting an Image with the CLI Deleting a Software ImageDeleting an Image with the Element Manager GUI Select Maintenance File ManagementCisco SFS 3012R Server Switch LEDs LED State Indication Cisco SFS 3012R Server Switch System Status LEDPower Supply LEDs Power Supply LEDsBlower Module LEDs Blower Module LEDsBlower LED States Indication Controller LEDsController LED States Indication Location of Management Ethernet Port LEDs Power LED States IndicationLED States Indication InfiniBand Switch Module LEDsInfiniBand LEDs InfiniBand Port LEDs Fibre Channel Gateway LEDs Fibre Channel LEDsOff Gbps Solid green Fibre Channel Port LEDsLocation of Ethernet Gateway and Ethernet Port LEDs Ethernet Gateway LEDsEthernet Port LEDs Ethernet Gateway LEDsSpecification Detail General SpecificationsCertifications/Regulatory Electrical SpecificationsLaser Specifications D E IN-2 IN-3 IN-4
Top Page Image Contents