Extron electronic 68-1370-50 REV. C, DXP HDMI Edid Extended Display Identification Data, Mlp

Page 29

EDID (Extended Display Identification Data)

EDID is a communications protocol or instruction set for the identification of display devices to computers using the DDC (Display Data Channel) transmission standard. EDID information consists of the resolution, refresh rate, and pixel clock information of a display device.

You can apply an EDID to a selected input by selecting one of the following categories of EDID files, shown in the EDID table on the next page.

•• The EDID of the display connected to an output (numbers 1 through the number of outputs on your DXP)

•• One of 28 factory-loaded EDID files (numbers 9 through 36)

•• One of the four user-defined files, to which you have assigned your own EDID values (numbers 37 through 40)

NOTES: • Multi-channel audio consists of:
PCM	2-channel audio (stereo)	DTS	8-channel audio
AC-3	6-channel audio	E-AC-3	8-channel audio
PCM	8-channel audio	DTS-HD	8-channel audio
AC-3	8-channel audio	MLP	8-channel audio

• 2-channel audio consists of PCM, 2-channel audio (stereo).

DXP DVI Pro and DXP HDMI Series • Remote Control

23

Image 29

Contents DXP Hdmi Avertissement AchtungVorsicht PrecaucionFCC Class a Notice 安全须知中文Conventions Used in this Guide Contents Vi DXP DVI Pro and DXP Hdmi Series Contents About this Guide About the DXP DVI Pro and DXP Hdmi Series Matrix SwitchersTypical DXP DVI Pro Application Application Diagram ExamplesTypical DXP Hdmi Application DXP DVI Pro and DXP Hdmi Series Introduction Setup Procedure SetupDXP DVI Pro Rear Panel Rear Panels and ConnectionsInstalling the LockIt Lacing Bracket Input connectorsRJ-45 Connector and Pinout Tables Output connectorsDXP DVI Pro and DXP Hdmi Series Setup Remote RS232/RS422 Connector Front Panel Config PortMm Connector Cable for the Configuration Port DXP DVI Pro and DXP Hdmi Series Introduction DXP Switchers Front Panel Front Panel FeaturesDXP DVI Pro and DXP Hdmi Series Operation Creating a Tie OperationsLocking and Unlocking the Front Panel Executive Modes Saving or Recalling a PresetSelecting lock mode 2 or toggling between lock modes 2 To toggle mute on and off, press and hold Viewing Ties and Muting OutputsRS-232/RS-422 and Baud Rate Display RS-232/RS-422 and Baud Rate Selection Establishing a Network Ethernet Connection Remote ControlConnection Timeouts SIS CommandsVerbose Mode Host-to-switcher InstructionsMLP Edid Extended Display Identification Data720p default Edid Table DDC Source Selection SIS Value Resolution Refresh@*X# Command and Response Table for SIS Commands@*X#% @*X#$@*% InX@Vid InX@RGB@*$ InX@Aud Tie an Input to All OutputsX1 X2. . . Xn Front Panel Lock Executive Modes Edid Extended Display Identification Data CommandsInformation Requests X1 =X1$ X X1%A X1$ X X1% X1X1X1&X1*X$ IP SetupIpiX3 IpsX3EX4 DH IdhX4 EX3 CG IpgX3X5* TC EX5# CV VrbX5#Factory default settings Clear all ties and presets and reset unit toSoftware Button on the Software DVD Window Installing the ProgramStarting the Program Matrix Switchers Control Program Install LinkPassword Prompt for Control Program Loading the Start-up Accessing the Html PagesPassword Prompt for Web Pages System Settings Using the Web Pages to Configure the DXPControl DXP DVI Pro and DXP Hdmi Series Remote Control Europe, Africa, and the Middle China East USA, Canada, South America Japan Central AmericaAsia Middle East EuropeExtron Europe Extron India