Extron electronic 68-1370-50 REV. C, DXP HDMI setup guide 安全须知 中文, FCC Class a Notice

Page 3

安全须知 中文

这个符号提示用户该设备用户手册中 有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴

露的危险电压,有触电危险。

注意

阅读说明书 用 户 使 用 该 设 备 前 必 须 阅 读 并 理

解 所 有 安 全 和 使 用 说 明 。

保存说明书 用户应保存安全说明书以备将来使

用。

遵守警告 用户应遵守产品和用户指南上的所有安

全和操作说明。

避免追加 不要使用该产品厂商没有推荐的工具或 追加设备,以避免危险。

警告

电源 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线 ( 地 线 ) 是 安 全 设 施 , 不 能 不 用 或 跳 过 。

拔掉电源 为安全地从设备拔掉电源,请拔掉所有设备后

或桌面电源的电源线,或任何接到市电系统的电源线。 电源线保护 妥善布线, 避免被踩踏,或重物挤压。

维护 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。

通风孔 有些设备机壳上有通风槽或孔,它们是用来防止

机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 不正确的更换电池会有爆炸的危险。 必须使用

与厂家推荐的相同或相近型号的电池。 按照生产厂的 建议处理废弃电池。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This device may not cause harmful interference.

2.This device must accept any interference received, including interference that may cause undesired operation.

The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits.

Image 3
Contents DXP Hdmi Precaucion AchtungAvertissement VorsichtFCC Class a Notice 安全须知 中文Conventions Used in this Guide Contents Vi DXP DVI Pro and DXP Hdmi Series Contents About this Guide About the DXP DVI Pro and DXP Hdmi Series Matrix SwitchersTypical DXP DVI Pro Application Application Diagram ExamplesTypical DXP Hdmi Application DXP DVI Pro and DXP Hdmi Series Introduction Setup Procedure SetupDXP DVI Pro Rear Panel Rear Panels and ConnectionsInstalling the LockIt Lacing Bracket Input connectorsRJ-45 Connector and Pinout Tables Output connectorsDXP DVI Pro and DXP Hdmi Series Setup Remote RS232/RS422 Connector Front Panel Config PortMm Connector Cable for the Configuration Port DXP DVI Pro and DXP Hdmi Series Introduction DXP Switchers Front Panel Front Panel FeaturesDXP DVI Pro and DXP Hdmi Series Operation Creating a Tie OperationsLocking and Unlocking the Front Panel Executive Modes Saving or Recalling a PresetSelecting lock mode 2 or toggling between lock modes 2 To toggle mute on and off, press and hold Viewing Ties and Muting OutputsRS-232/RS-422 and Baud Rate Display RS-232/RS-422 and Baud Rate Selection Establishing a Network Ethernet Connection Remote ControlHost-to-switcher Instructions SIS CommandsConnection Timeouts Verbose ModeMLP Edid Extended Display Identification Data720p default Edid Table DDC Source Selection SIS Value Resolution Refresh@*X#$ Command and Response Table for SIS Commands@*X# @*X#%Tie an Input to All Outputs InX@RGB@*% InX@Vid @*$ InX@AudX1 X2. . . Xn Front Panel Lock Executive Modes Edid Extended Display Identification Data CommandsX1 = X1$ X X1%A X1$ X X1%Information Requests IpsX3 IP SetupX1X1X1&X1*X$ IpiX3EX5# CV VrbX5# EX3 CG IpgX3EX4 DH IdhX4 X5* TCFactory default settings Clear all ties and presets and reset unit toSoftware Button on the Software DVD Window Installing the ProgramStarting the Program Matrix Switchers Control Program Install LinkPassword Prompt for Control Program Loading the Start-up Accessing the Html PagesPassword Prompt for Web Pages System Settings Using the Web Pages to Configure the DXPControl DXP DVI Pro and DXP Hdmi Series Remote Control Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle EastExtron Europe Extron India