Extron electronic 42-122-xx manual Power Module, Connect wires to AC receptacle

Extron electronic 42-122-xx manual Introduction, Overview, AVTrac Floor System
Extron electronic 42-122-xx manual Kit Contents
Extron electronic 42-122-xx manual Kit Contents
Extron electronic 42-122-xx Before Getting Started, Planning, Floor Considerations, In-Wall Cable Routing Considerations
Extron electronic 42-122-xx manual Room Considerations, Wheelchair Accessibility, AVTrac maximum slope is
Extron electronic 42-122-xx manual Before Getting Started, cont’d, Tools and Equipment Required for Installation
Extron electronic 42-122-xx manual Installation, Floor, Remove carpet tiles to expose concrete
Extron electronic 42-122-xx manual Wall, Mark wall, Cut cable access hole in wall
Extron electronic 42-122-xx manual Track, Cut aluminum base track, Measure and cut track
Extron electronic 42-122-xx manual Track, cont’d, Pre-drill holes in track and ramps, Positions of mounting holes Extron electronic 42-122-xx manual Mate side ramp to base track, Drill into concrete and screw down track Extron electronic 42-122-xx manual Connectivity Box, Secure connectivity box to the floor
Extron electronic 42-122-xx manual Power Module, Connect wires to AC receptacle
Extron electronic 42-122-xx Power Module cont’d, Attach AC power module, Connect double isolated cable to junction box
Extron electronic 42-122-xx manual Install AAPs, Run cable to AAPs
Extron electronic 42-122-xx manual Finishing Up, Ensure cables lay flat, Fit cover track, Cut carpet
Extron electronic 42-122-xx manual Refit carpet, Use template to cut base board Reattach base board to wall
Extron electronic 42-122-xx manual Finishing up cont’d, AVTrac installed
Extron electronic 42-122-xx manual Reference Material, Specifications
Extron electronic 42-122-xx manual Cont’d, AVTrac 480R
Extron electronic 42-122-xx manual Connectivity box
Extron electronic 42-122-xx manual Universal AC Compatibility Guide, Usa
Extron electronic 42-122-xx manual Optional Accessories, Track Accessories, Active AAPs, Passive AAPs
Extron electronic 42-122-xx manual Reference Material Extron electronic 42-122-xx manual Extron’s Warranty Extron electronic 42-122-xx manual Quick Installation Checklist, Before Getting Started
Page 15

Installation

Step 5: Power Module

By this point, the connectivity box must be securely fastened to the floor.

If the AVTrac system does not include the AC power module, ignore this section. To attach the AC power module, follow these instructions:

WSwitch off all electrical power before connecting the AC conduit to a junction box, and keep power off until installation is complete.

CAll electrical installation should be performed by qualified personnel in accordance with local and national electrical codes.

(F)

(J)

(D)

(E)

Receptacles for the AC power modules are available in Australian (F), universal (J), central European (D), and French (E) models. The Australian and Universal models are provided with 24' of metal conduit, without wires (CO models). The Central European, French, and Universal models are provided with 24' of double insulated cable (ISO models).

NSome plug types are not fully compatible with the Universal Receptacle. For more details refer to the Universal AC Outlet Compatibility Guide on page 22.

5-1Connect wires to models with the unwired metal conduit (Australian and Universal CO models) by threading wires through the conduit using fish tape or similar device. Remove 1/8" (3 mm) of insulation from both ends of each wire.

Loosen the holding screws in the AC receptacle.

Insert the wire into appropriate hole and tighten the holding screws.

Snap the AC receptacle into power module.

WThe blue or black wire must be connected to the neutral slot, the brown or red wire must be connected to the live slot, and the solid green or green and yellow striped wire must be connected to the ground.

 

Green

 

Brown

or Green/

Blue or

Yellow

or Red

(ground)

Black

(live)

 

(neutral)

L N

Connect wires to AC receptacle

AVTrac • Installation

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents AVTrac Installation GuideSicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisIntroduction OverviewAVTrac Floor System Kit Contents Kit Contents In-Wall Cable Routing Considerations Before Getting StartedPlanning Floor ConsiderationsWheelchair Accessibility Room ConsiderationsAVTrac maximum slope is Before Getting Started, cont’d Tools and Equipment Required for InstallationCut prelaid carpet roll to expose concrete InstallationFloor Remove carpet tiles to expose concreteCut cable access hole in wall WallMark wall Track Cut aluminum base trackMeasure and cut track Pre-drill holes to secure connectivity box Track, cont’dPre-drill holes in track and ramps Positions of mounting holesMate side ramp to base track Drill into concrete and screw down trackScrew side ramps to floor Secure connectivity box to the floor Connectivity BoxConnect wires to AC receptacle Power ModuleConnect AC conduit to junction box Power Module cont’dAttach AC power module Connect double isolated cable to junction boxInstall AAPs AAPsRun cable to AAPs Cut carpet Finishing UpEnsure cables lay flat Fit cover trackRefit carpet Use template to cut base board Reattach base board to wallAttach carpet tile to track raceway Finishing up cont’d AVTrac installedReference Material SpecificationsAVTrac 480R Cont’dConnectivity box USA Universal AC Compatibility GuidePassive AAPs Optional AccessoriesTrack Accessories Active AAPsReference Material Extron’s Warranty Before Getting Started Quick Installation Checklist
Top Page Image Contents