Extron electronic 42-122-xx manual Quick Installation Checklist, Before Getting Started

Page 28

Quick Installation Checklist

Installation of the AVTrac can be divided into six main sections:

Step 1 — Before Getting Started

†† Decide where the Track will be placed (pages 4 and 5) and, if necessary, prepare the site.

†† Open the two boxes containing the AVTrac kit and identify all the items provided (pages 2 and 3).

†† Gather any additional tools needed for installation (page 6).

Step 2 — Install Track

†† Remove existing carpeting (page 7).

†† If cables will be run through a drywall cavity, cut a hole in drywall (page 8). †† Measure and cut track pieces (page 9).

†† Secure the track to the floor (pages 10 and 11).

Step 3 — Install Connectivity Box

†† Remove the top cover and end plates from connectivity box (page 10) and place the box on the track (page 12).

†† Secure the connectivity box to the track and floor (page 12).

Step 4 — Install AC Power Module

†† If necessary, wire the AC power receptacle (page 13).

†† Seat and secure AC power module in connectivity box (page 14). †† Run AC conduit and connect to junction box (page 14).

Step 5 — Install Architectural Adapter Plates

†† Install AAPs in connectivity box cover panel (page 15). †† Run and connect cables to the AAPs (page 15).

†† Reattach the end plates and cover panel (page 15).

Step 6 — Finishing Up

†† Snap on cover track (page 16).

†† Cut and glue carpet to side and end ramps (pages 16 and 17).

†† Trim wall baseboards and apply carpet or rubber strip finish to cover track raceway (page 17).

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500 +1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794 +1.919.863.1797 FAX

Extron EMEA

Extron Asia

Extron Japan

+800.3987.6673

+800.7339.8766

+81.3.3511.7655

Inside Europe Only

Inside Asia Only

+81.3.3511.7656 FAX

+31.33.453.4040

+65.6383.4400

 

+31.33.453.4050 FAX

+65.6383.4664 FAX

 

 

 

 

© 2008 Extron Electronics. All rights reserved.

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568 +86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800 +971.4.2991880 FAX

AVTrac • Quick Installation Checklist

Page 27 Page 28
Image 28
Page 27 Page 28
Contents Installation Guide AVTracPrecautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschOverview IntroductionAVTrac Floor System Kit Contents Kit Contents Before Getting Started PlanningFloor Considerations In-Wall Cable Routing ConsiderationsRoom Considerations Wheelchair AccessibilityAVTrac maximum slope is Tools and Equipment Required for Installation Before Getting Started, cont’dInstallation FloorRemove carpet tiles to expose concrete Cut prelaid carpet roll to expose concreteWall Cut cable access hole in wallMark wall Cut aluminum base track TrackMeasure and cut track Track, cont’d Pre-drill holes in track and rampsPositions of mounting holes Pre-drill holes to secure connectivity boxDrill into concrete and screw down track Mate side ramp to base trackScrew side ramps to floor Connectivity Box Secure connectivity box to the floorPower Module Connect wires to AC receptaclePower Module cont’d Attach AC power moduleConnect double isolated cable to junction box Connect AC conduit to junction boxAAPs Install AAPsRun cable to AAPs Finishing Up Ensure cables lay flatFit cover track Cut carpetUse template to cut base board Reattach base board to wall Refit carpetAttach carpet tile to track raceway AVTrac installed Finishing up cont’dSpecifications Reference MaterialCont’d AVTrac 480RConnectivity box Universal AC Compatibility Guide USAOptional Accessories Track AccessoriesActive AAPs Passive AAPsReference Material Extron’s Warranty Quick Installation Checklist Before Getting Started
Top Page Image Contents