ATTO Technology SC 5700 IPSubnetMask, IsReserved, MaxOpTemp, Metrics, MinOpTemp, OpTempWarn

Page 58

IPSubnetMask

Controls the current subnet masks used by any Ethernet port(s) on the unit. If IPDHCP is enabled, the get command reports the current IP subnet mask assigned by the network DHCP server.

Default: 255.255.0.0

set IPSubnetMask [mp1] [xxx.xxx.xxx.xxx] SaveConfiguration Restart command required get IPSubnetMask [mp1]

IsReserved

Displays the reservation status of the current unit.

IsReserved

MaxOpTemp

Regulates the maximum operating temperature of this unit in degrees Celsius. Valid entries are between 55 and 70 degrees.

Default: 70

set MaxOpTemp [55 – 70] SaveConfiguration Restart command required get MaxOpTemp

Metrics

Controls the collection of standard data metrics within a product.

Metrics [Start Stop Display Clear] [[drive [BlockDevID] all running]

MinOpTemp

Regulates the minimum operating temperature of this unit in degrees Celsius. Valid entries are between 0 and 15 degrees.

Default: 0

set MinOpTemp [0 – 15]

SaveConfiguration Restart command required get MinOpTemp

OpTempWarn

Regulates the number of degrees Celsius before a thermal control event precipitates a warning to the user. Valid entries are between 0 and 15 degrees.

Default: 5

set OpTempWarn [0 – 15]

SaveConfiguration Restart command required get OpTempWarn

Partition

Sets the specified partition to the specified capacity in gigabytes (GB), megabytes (MB), or blocks. The specified capacity must be smaller than the specified partition’s current capacity. A new partition is created to acquire the remainder of the original partition’s space. VirtualDriveInfo displays characteristics and statistics for all the available virtual drives or any available virtual drive identified by its virtual drive ID.

Partition [GroupName] [partition index] [capacity] [GB MB blocks]

xi

PartitionDisplay

Lists all the partitions available in the specified RAID group. The partitions are listed in order of contiguousness (as opposed to index order).

PartitionDisplay [GroupName]

PartitionMerge

Combines the specified contiguous partitions into one partition. Partition index is the index of a partition to merge, along with a number of contiguous partitions to merge to that index. All indicates that all partitions in the RAID group are merged into a single Virtual Disk. The RAID group must not be in a NEW state. None of the partitions to merge may be mapped.

PartitionMerge [GroupName] [[[partition index] [2-128]] all]

PartitionSplit

Divides the specified partition into one or more partitions whose capacities are evenly distributed among the capacity of the original partition. The partition to split cannot be mapped. The RAID group must not be in a NEW state.

PartitionSplit [GroupName] [partition index] [2-128]

PartitionWriteCache

If enabled, allows higher write performance with a small risk of data loss after a system failure. If disabled, provides a higher level of data integrity with lower write performance.

set PartitionWriteCache [GroupName] {PartIndex] [enabled disabled]

get PartitionWriteCache [GroupName] {PartIndex]

PassThroughMode

SC 5500, 5700

Specifies the non-disk device types which are automatically mapped at boot time. The all option allows all non-disk devices to be mapped. The SES option allows dedicated SES processor LUNs to be mapped. The non-SES option allows all non-SES devices to be mapped. The disabled option disables the pass- through mode.

Default: disabled

set PassThroughMode [all SES non-SES disabled] get PassThroughMode

PassThroughPersistent

SC 5500, 5700

Stores maps for currently-attached passthrough devices to persistent memory,

PassThroughPersistent

ATTO Technology Inc. FastStream SC Installation and Operation Manual

Page 57 Page 59
Image 58
Page 57 Page 59
Contents FastStream SC Atto Technology, Inc Contents Phone Home Email Alerts Drive Diagnostics Configure Storage into RAID GroupsMonitor Storage, Configurations Scsi Enclosure Services SESInterface Options Manage Atto Devices, ConfigurationsAppendix E Warranty Xxvi Appendix B Design RAID Groups XixAudio/video features FastStream 5000 Series featuresRAID protection features Additional FastStream 5300 featuresAdditional FastStream 5500 features Additional FastStream 5700 featuresFastStream SC 5300 Physical Attributes Exhibit 1.1-1 The connector side of the FastStream SC5300 FastStream SC 5500 Physical Attributes Reset/restore factory default switchOperating Temperature 5 C-40 C SAS/SATA portsLEDs on the faceplate are Cooling and airflow Fibre Channel ports FastStream SC 5700 Physical AttributesDo not block the enclosure’s vents. Page Installing the FastStream Install the FastStream Storage ControllerUnpacking the packing box verifying contents Setting up Internet ExplorerSelect Internet Options Beginning initial configurationUncheck the Require server verification check box Before creating RAID groups Ensure Drive IntegritySelect Initialize and Verify Drives After creating RAID groups Features you may choose Configure Storage into RAID GroupsAuto-Rebuild Initialization Fault ToleranceSelecting an application Preliminary stepsGeneral Digital Video, General IT or Database Quick Digital VideoAudio Click CommitCreating a custom setup Page Page Modify System Values Changing current user name, passwordCreating a read-only user name, password Changing system variablesWhen you have completed your changes, click on Commit Health and Status Monitor Monitor Storage, ConfigurationsHealth and Status Monitor page appears Configuration Display Scsi Enclosure Services SESConfiguration Click the Set up Error Notification buttonPhone Home Email Alerts Exhibit 6.1-1 The Error Notification Read only drive test Drive DiagnosticsClick the Read-Only Drive Test button Identifying a drive attached to the FastStream Drive performance and healthClick on Identify Drive Scsi Enclosure Services SES Setting up SESIdentifying SES elements Monitoring SES elements Use the Health and Status MonitorSelect the Monitor Enclosure Services button Use the Manage menuCreating RAID groups Modify StorageRAID group processes Deleting RAID groupsChanging RAID configuration RAID migration Adding mirrors to a RAID configurationAdding drives to a RAID group Rebuilding RAID groups Modifying RAID group mappingModifying RAID group partitions Click on the Modify RAID Group Mapping buttonModifying RAID options FastStream process adding or removing Hot SparesSelect the Add/Remove Hot Spares button Removing RAID configuration data Advanced CLIPage Discovering, managing other Atto devices Manage Atto Devices, ConfigurationsCreating a unique name for your FastStream Appliance NameSaving or restoring a configuration Click on the System Configuration Save/Restore buttonUsing the ExpressNAV Storage Manager Interface OptionsType FastStream in the New Connection dialog box Using the serial portUsing Telnet EnterUpdate Firmware Click UploadPage Symbol/Abbreviation Indicates Appendix a CLI Provides an ASCII-based InterfaceCLI error messages CLI summaryCommand Default Example IiiIpdhcp Command Default Example AutoMap CLI command explanationsAutoResume DefaultInterleave BlockDevCleanBoot Delay BlockDevIdentifyEmailPassword DriveTestConfigDumpConfiguration DriveTestEventLog FCPortErrorsEthernetSpeed EventLogFilterFCTargets FCPortListFCSCSIBusyStatus FCWWNameMaxOpTemp IPSubnetMaskIsReserved MetricsResetFCPortErrors PasswordReadOnlyPassword RestoreConfigurationRGCommit RGCancelAddStorageRGAutoRebuild RGCreateRGRebuild RGWaitTimeoutRGPreFetch RGResumeConversionRoute SaveConfigurationRMStatus RouteDisplaySerialPortBaudRate SCSIPortResetSCSIPortResetOnStartup SerialPortEchoSESEnclosures SESDiskFailureAlarmDefault disabled SESIdentifyTime TemperatureTailEventLog TimeZoneJbod Just a Bunch of Disks Appendix B Design RAID GroupsDvraid Digital Video RAID RAID Level 1 mirroring duplicate drives RAID Level 0 striping, no redundancyRAID Level 1 plus additional mirroring RAID Level 4 striping, one parity drive RAID Level 1+0 striping, mirror spans two drivesRAID Level 5 striping, parity distributed among drives Disk Stripe Data Appendix C Scsi Cabling Connecting Scsi devices to Scsi portsCable types Support Max Bits EndedAppendix D Standards and Compliances Declaration of ConformityAppendix E Warranty Manufacturer limited warranty
Top Page Image Contents