TP-Link TD-W8960N manual Quick Installation Guide, TCP/IP Configuration

Page 15

TD-W8960N Wireless N ADSL2+ Modem Router User Guide

Chapter 3. Quick Installation Guide

This chapter will show you how to configure the basic functions of your TD-W8960N Wireless N ADSL2+ Modem Router using Quick Setup Wizard within minutes.

3.1 TCP/IP Configuration

The default IP address of the Router is 192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.

Connect the local PC to the LAN ports of the Router. And then you can configure the IP address for your PC in the following two ways.

1.Configure the IP address manually

1)Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC".

2)Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1 (The Router's default IP address)

2.Obtain an IP address automatically

1)Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC”.

2)Then the built-in DHCP server will assign IP address for the PC.

Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows XP OS.

Open a command prompt, and type ping 192.168.1.1, and then press Enter.

3.If the result displayed is similar to the Figure 3-1,it means the connection between your PC and the Router has been established well.

8

Image 15

Contents TD-W8960N Wireless N ADSL2+ Modem Router Copyright & Trademarks FCC Statement 2400.0-2483.5 MHz Country Restriction Reason/remark CE Mark WarningZhao Jianjun Director of International Business Declaration of ConformityContents Wireless Package Contents Incredible Speed Flexible Access ControlSimple Installation Overview of the RouterMain Features Panel Layout Front PanelName Status Description Back Panel Installation Environment Requirements Connecting the RouterSystem Requirements TD-W8960N Wireless N ADSL2+ Modem Router User Guide TCP/IP Configuration Quick Installation GuidePlease check the connection following these steps Failure result of Ping commandQuick Installation Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide Device Info LoginAdvanced Setup Quick SetupLayer2 Interface TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide WAN Service ATM-EoA-PPPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide ATM-EoA-IPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide ATM-EoA-Bridge ATM-PPPoA ATM-IPoAETH-PPPoE 3 LAN ETH-IPoEETH-Bridge TD-W8960N Wireless N ADSL2+ Modem Router User Guide MAC Address Clone 5 NAT To add a virtual server entry Virtual ServersTD-W8960N Wireless N ADSL2+ Modem Router User Guide To add a new Port Triggering Port TriggeringDMZ Host Security To add a new DMZ HostIP Filtering Setup an Outgoing IP Filtering rule Setup an Incoming IP Filtering rule MAC Filtering To add a MAC Filtering rule Time Restriction Parental ControlTo add a Time Restriction entry for Parental Control rule To add a URL Filter entry for Parental Control rule URL FilterQuality of Service QoS Classification Routing Static Route Default GatewayTo remove a static routing entry To add static routing entries10 DNS 9.3 RIPDNS Server Dynamic DNS To add a Ddns entry Upnp 11 DSLInterface Grouping Dns ProxyTo create a new interface group TD-W8960N Wireless N ADSL2+ Modem Router User Guide LAN Ports IPSec Click Save/Apply to save this entry Basic WirelessWSC Setup By PBC Method Two II. By PIN TD-W8960N Wireless N ADSL2+ Modem Router User Guide WEP Manual Setup APConfigure WEP Encryption WPA WPA-PSK Configure WPA settingsWPA2 Configure WPA-PSK settingsMixed WPA2/WPA WPA2-PSKMixed WPA2/WPA-PSK MAC FilterForm of MAC Address must be xxxxxxxxxxxx, like 00130A55FF09 Wireless Bridge¾ Bridge Restrict Advanced TD-W8960N Wireless N ADSL2+ Modem Router User Guide Station info DiagnosticsManagement SettingsTo back up the Router’s current settings BackupTo update the Router’s settings UpdateTo Configure the System Log Settings System LogTo View the System Log Snmp Agent 4 TR-069 client TD-W8960N Wireless N ADSL2+ Modem Router User Guide Access Control- Passwords Internet TimeTo set the Router’s time To change the password Update SoftwareTo update the Routers software RebootWant to use NetMeeting, what do I need to do? Appendix a FAQWant to build a WEB Server on the LAN, what should I do? Wireless stations cannot connect to the Router Configure TCP/IP component Appendix B Configuring the PCTD-W8960N Wireless N ADSL2+ Modem Router User Guide ¾ Setting IP address manually Now Wireless GeneralEnvironmental and Physical Appendix D Glossary TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide

Related manuals

Manual 122 pages 33.92 Kb