TP-Link manual TD-W8960N Wireless N ADSL2+ Modem Router User Guide

Page 82

TD-W8960N Wireless N ADSL2+ Modem Router User Guide

Figure 4-94

¾Channel: Select the channel you want to use from the drop-down List. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

¾Mode: In the drop-down list you can select “11b”, “11bg”, “11bgn” and "11n only”. “11bgn” allows both 802.11b, 802.11g and 802.11n wireless stations to connect to the Router,

¾Bandwidth: Select the Bandwidth you want to use from the drop-down List. If bigger bandwidth is selected, device could transmit and receive data with higher speed.

¾Control Sideband: If bigger bandwidth is selected, this option will allow you select the Control Sideband you want.

¾Fragmentation Threshold: This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.

¾RTS Threshold: Should you encounter inconsistent data flow, only minor reduction of the default value 2347 is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. In most cases, keep its default value of 2347.

¾DTIM Interval: This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1.

75

Page 81 Page 83
Image 82
Page 81 Page 83
Contents TD-W8960N Wireless N ADSL2+ Modem Router Copyright & Trademarks FCC Statement CE Mark Warning 2400.0-2483.5 MHz Country Restriction Reason/remarkDeclaration of Conformity Zhao Jianjun Director of International BusinessContents Wireless Package Contents Overview of the Router Flexible Access ControlSimple Installation Incredible SpeedMain Features Front Panel Panel LayoutName Status Description Back Panel Connecting the Router Installation Environment RequirementsSystem Requirements TD-W8960N Wireless N ADSL2+ Modem Router User Guide Quick Installation Guide TCP/IP ConfigurationFailure result of Ping command Please check the connection following these stepsQuick Installation Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide Login Device InfoQuick Setup Advanced SetupLayer2 Interface TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide WAN Service ATM-EoA-PPPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide ATM-EoA-IPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide ATM-EoA-Bridge ATM-IPoA ATM-PPPoAETH-PPPoE ETH-IPoE 3 LANETH-Bridge TD-W8960N Wireless N ADSL2+ Modem Router User Guide MAC Address Clone 5 NAT Virtual Servers To add a virtual server entryTD-W8960N Wireless N ADSL2+ Modem Router User Guide Port Triggering To add a new Port TriggeringDMZ Host To add a new DMZ Host SecurityIP Filtering Setup an Outgoing IP Filtering rule Setup an Incoming IP Filtering rule MAC Filtering To add a MAC Filtering rule Parental Control Time RestrictionTo add a Time Restriction entry for Parental Control rule URL Filter To add a URL Filter entry for Parental Control ruleQuality of Service QoS Classification Routing Default Gateway Static RouteTo add static routing entries To remove a static routing entry9.3 RIP 10 DNSDNS Server Dynamic DNS To add a Ddns entry 11 DSL UpnpDns Proxy Interface GroupingTo create a new interface group TD-W8960N Wireless N ADSL2+ Modem Router User Guide LAN Ports IPSec Click Save/Apply to save this entry Wireless BasicWSC Setup By PBC Method Two II. By PIN TD-W8960N Wireless N ADSL2+ Modem Router User Guide Manual Setup AP WEPConfigure WEP Encryption WPA Configure WPA settings WPA-PSKConfigure WPA-PSK settings WPA2WPA2-PSK Mixed WPA2/WPAMAC Filter Mixed WPA2/WPA-PSKWireless Bridge Form of MAC Address must be xxxxxxxxxxxx, like 00130A55FF09¾ Bridge Restrict Advanced TD-W8960N Wireless N ADSL2+ Modem Router User Guide Diagnostics Station infoSettings ManagementBackup To back up the Router’s current settingsUpdate To update the Router’s settingsSystem Log To Configure the System Log SettingsTo View the System Log Snmp Agent 4 TR-069 client TD-W8960N Wireless N ADSL2+ Modem Router User Guide Internet Time Access Control- PasswordsTo set the Router’s time Update Software To change the passwordReboot To update the Routers softwareAppendix a FAQ Want to use NetMeeting, what do I need to do?Want to build a WEB Server on the LAN, what should I do? Wireless stations cannot connect to the Router Appendix B Configuring the PC Configure TCP/IP componentTD-W8960N Wireless N ADSL2+ Modem Router User Guide ¾ Setting IP address manually Now General WirelessEnvironmental and Physical Appendix D Glossary TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide
Related manuals
Manual 122 pages 33.92 Kb
Top Page Image Contents