TP-Link TD-W8960N manual Diagnostics, Station info

Page 83

TD-W8960N Wireless N ADSL2+ Modem Router User Guide

¾Beacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default value is 100.

¾Transmit Power: This option will allow you to configure the wireless transmit power. High transmit power will extend the wireless signal range of the device and make the signal transmit more legible. Low transmit power with the smaller wireless signal range that will decrease the probability of interrupt by other Wi-Fi device.

¾WMM (Wi-Fi Multimedia): This function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended.

4.5.6 Station info

Choose “Wireless”Æ” Station info”, you will see the screen of Wireless-Authenticated Stations setting shown as below.

Figure 4-95

This page shows authenticated wireless stations and their status.

¾MAC: Displays the connected wireless station's MAC address.

¾Associated: Displays whether the wireless station has associated with the access point.

¾Authorized: Displays the information of Authentication.

¾SSID: Displays the connected wireless station's SSID.

¾Interface: Displays the connected wireless station's Interface mode.

4.6 Diagnostics

Choose “Diagnostics”, you will see the Diagnostics screen. This section describes the result of the test for the ENET (Ethernet) Connection, Wireless Connection and ADSL Synchronization. You can refer to the Help menu to get more information about the corresponding test.

76

Image 83

Contents TD-W8960N Wireless N ADSL2+ Modem Router Copyright & Trademarks FCC Statement 2400.0-2483.5 MHz Country Restriction Reason/remark CE Mark WarningZhao Jianjun Director of International Business Declaration of ConformityContents Wireless Package Contents Incredible Speed Flexible Access ControlSimple Installation Overview of the RouterMain Features Name Status Description Panel LayoutFront Panel Back Panel System Requirements Installation Environment RequirementsConnecting the Router TD-W8960N Wireless N ADSL2+ Modem Router User Guide TCP/IP Configuration Quick Installation GuidePlease check the connection following these steps Failure result of Ping commandQuick Installation Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide Device Info LoginAdvanced Setup Quick SetupLayer2 Interface TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide WAN Service ATM-EoA-PPPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide ATM-EoA-IPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide ATM-EoA-Bridge ETH-PPPoE ATM-PPPoAATM-IPoA ETH-Bridge 3 LANETH-IPoE TD-W8960N Wireless N ADSL2+ Modem Router User Guide MAC Address Clone 5 NAT To add a virtual server entry Virtual ServersTD-W8960N Wireless N ADSL2+ Modem Router User Guide To add a new Port Triggering Port TriggeringDMZ Host IP Filtering SecurityTo add a new DMZ Host Setup an Outgoing IP Filtering rule Setup an Incoming IP Filtering rule MAC Filtering To add a MAC Filtering rule Time Restriction Parental ControlTo add a Time Restriction entry for Parental Control rule To add a URL Filter entry for Parental Control rule URL FilterQuality of Service QoS Classification Routing Static Route Default GatewayTo remove a static routing entry To add static routing entriesDNS Server 10 DNS9.3 RIP Dynamic DNS To add a Ddns entry Upnp 11 DSLInterface Grouping Dns ProxyTo create a new interface group TD-W8960N Wireless N ADSL2+ Modem Router User Guide LAN Ports IPSec Click Save/Apply to save this entry Basic WirelessWSC Setup By PBC Method Two II. By PIN TD-W8960N Wireless N ADSL2+ Modem Router User Guide WEP Manual Setup APConfigure WEP Encryption WPA WPA-PSK Configure WPA settingsWPA2 Configure WPA-PSK settingsMixed WPA2/WPA WPA2-PSKMixed WPA2/WPA-PSK MAC FilterForm of MAC Address must be xxxxxxxxxxxx, like 00130A55FF09 Wireless Bridge¾ Bridge Restrict Advanced TD-W8960N Wireless N ADSL2+ Modem Router User Guide Station info DiagnosticsManagement SettingsTo back up the Router’s current settings BackupTo update the Router’s settings UpdateTo View the System Log To Configure the System Log SettingsSystem Log Snmp Agent 4 TR-069 client TD-W8960N Wireless N ADSL2+ Modem Router User Guide To set the Router’s time Access Control- PasswordsInternet Time To change the password Update SoftwareTo update the Routers software RebootWant to use NetMeeting, what do I need to do? Appendix a FAQWant to build a WEB Server on the LAN, what should I do? Wireless stations cannot connect to the Router Configure TCP/IP component Appendix B Configuring the PCTD-W8960N Wireless N ADSL2+ Modem Router User Guide ¾ Setting IP address manually Now Environmental and Physical WirelessGeneral Appendix D Glossary TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide TD-W8960N Wireless N ADSL2+ Modem Router User Guide

Related manuals

Manual 122 pages 33.92 Kb