Compaq LP8000-F1 manual Contents

Page 3

Contents

About This Guide

Text Conventions	vii
Symbols in Text	viii
Symbols on Equipment	viii
Getting Help	ix
Compaq Technical Support	ix
Compaq Website	x
Compaq Authorized Reseller	x

Chapter 1

Introduction

Overview	1-1
Product Description	1-1
Jumper Settings	1-3
Performance Specifications	1-4
Standards	1-4
Agency Approvals	1-5

Chapter 2

Installation

Installation Overview	2-1
Hardware Requirements	2-1
Software and Documentation Requirements	2-2
Recording Reference Numbers	2-3
Recording the Address and Serial Number	2-3
Installing the HBA into a Computer	2-3
Verifying the Installation	2-4
Configuration Guidelines for Operating Systems	2-4

Image 3

Contents Bit PCI-To-Fibre Channel Host Bus Adapter Page Contents Device Driver Installation Glossary Index List of Figures Text Conventions About This GuideSymbols on Equipment Symbols in TextCompaq Technical Support Getting HelpCompaq Website Compaq Authorized Reseller Introduction OverviewProduct Description Bit PCI-to-fibre channel host bus adapter Bit PCI-to-Fibre Channel Host Bus Adapter Jumper SettingsHBA Jumper Settings Jumper Pins Description Device ID CommentsStandards Performance SpecificationsAgency Approvals Page Installation Installation OverviewHardware Requirements Software and Documentation Requirements OEMSETUP.INF TXTSETUP.OEM Lpscsi LPUTILNT.EXEInstalling the HBA into a Computer Recording Reference NumbersRecording the Address and Serial Number Green LED Yellow LED State Verifying the InstallationConfiguration Guidelines for Operating Systems Post LED IndicatorsInstallation Page Device Driver Installation IntroductionWindows NT 4.0 System Requirements Installing the Windows NT Scsi Device Driver Removing the Device Driver Verifying the Device Driver InstallationTru64Unix Driver and Console Software Show Adapter / -SET Adapter CommandsWWIDMGR-SHOW Adapter Show Adapter CommandSET Adapter example OpenVMS Driver and Console Software Page Post Conditions and Results TroubleshootingWindows NT Event Viewer HBA Post LED StatesGreen LED Yellow LED Description Windows NT Scsi Port Error Log Windows NT Miniport Event Log CodesExplanation 0x10 Explanation 0x11to 0x13 Further Information Offset Windows NT Scsi Port Error LogWindows NT Scsi Port Error Log 0x10 Explanation Offset 0xF3 0xF4 HBA reset0x11 to 0x13 Further Information 0x12 Offset Explanation Parameter Error Values valid only when CmdStat=0x3CmdStat Values Further Information0x12 Offset Parameter Error Values valid only when CmdStat=0x3Fabric Device Mapping Windows NT Scsi Address MappingNone Private Loop Device MappingCurrent Private Loop Device Mapping Bus # Target# Lun#Current Private Loop Device Mapping Current Private Loop Device Mapping Bus # Target# Lun# Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Page Diagnostic and Firmware Download Utility Firmware and Diagnostic UtilityStarting I386DNLD.EXE in an i386 System I386 System InstallationStarting Alpha Systems with Alpha Bios I386DNLD.EXE Command OptionsOption Description Start-Up for Alpha/i386 Systems Return Diagnostics Main Menu I386DNLD.EXE Main Menu OptionsMenu Selection Restart Host Bus Adapters MaintenanceTest Host Bus Adapters Modify Test OptionsDiagnostic and Firmware Loader Utility Show Host Bus Adapter InfoQuit Firmware and Diagnostic Utility Page Using Lputilnt Utility/NT Main menu screen Viewing HBA ParametersUsing the Lputilnt Utility/NT Performing HBA Firmware MaintenanceFirmware maintenance screen Deleting or Activating Firmware Image Upgrading HBA FirmwareEnabling or Disabling Boot Bios Downloading PCI Configuration FilesModifying the Driver Parameters Modifying Driver Parameters Windows NT RegistryParameter Drive ParametersQueueDepth = n QueueTarget = n Parameter DescriptionDrive Parameters AlPA Addresses Page System Requirements Boot BiosRA8000 or ESA12000 Boot Setup Auto-Configure OptionDisk In-line Exerciser Boot Bios Enabling Boot Bios Defining a Fibre Channel Drive as Boot DriveDesignating a Fibre Channel Boot Drive on Your Computer Creating an MS-DOS Boot DiskettePageUp key Purpose Enabling HBA Boot Bios on a Fibre Channel Hard DriveEnabling the Boot Bios Formatting the Fibre Channel Drive on Your ComputerPage Installing Windows NT Page FCC Compliance Information Statement Model LP8000-F1 1 X Regulatory Compliance NoticesPage Federal Communications Commission Notice Reference Manual Statements for Class B EquipmentPage Glossary Page Glossary Page Glossary Page Show ADAPTER/-SET Adapter IndexPage Index Page