Compaq LP8000-F1 manual Diagnostics Main Menu, I386DNLD.EXE Main Menu Options, Menu Selection

Page 54

5-6Compaq StorageWorks 64-Bit PCI-To-Fibre Channel Host Bus Adapter User Guide

Diagnostics Main Menu

After the diagnostic and firmware download utility goes through its start-up procedure, the Main menu displays and handles user requests. If the program detects two or more HBAs in the system, you are prompted to select which HBA(s) is to be tested.

The function of each option on the Main menu is listed in Table 5-2.

Table 5-2

I386DNLD.EXE Main Menu Options

Menu Selection

Test Host Adapters

Modify Test Options

Restart Host Adapters

Input/Output

Maintenance

Show Host Adapters Info

Quit

Description

Runs host-based internal and external loopback tests.

Enables you to disable or enable up to seven different tests, depending upon the cards installed (BIU-1 or BIU-2). Specify number of retries and actions to take if error occurs.

Resets the HBA.

Opens or closes input and output files.

Updates firmware or non-volatile parameters in FLASH ROM. Display program images stored in memory.

Displays configuration and status data used by Tech Support.

Exits I386DNLD.EXE.

NOTE: Enter 0 at the Option prompt to display the previous menu. All values are in hexadecimal.

The menu options and descriptions are described in the following sections.

Image 54
Contents Bit PCI-To-Fibre Channel Host Bus Adapter Page Contents Device Driver Installation Glossary Index List of Figures About This Guide Text ConventionsSymbols in Text Symbols on EquipmentGetting Help Compaq Technical SupportCompaq Website Compaq Authorized Reseller Introduction OverviewProduct Description Bit PCI-to-fibre channel host bus adapter Jumper Pins Description Device ID Comments Jumper SettingsHBA Jumper Settings Bit PCI-to-Fibre Channel Host Bus AdapterPerformance Specifications StandardsAgency Approvals Page Installation Installation OverviewHardware Requirements OEMSETUP.INF TXTSETUP.OEM Lpscsi LPUTILNT.EXE Software and Documentation RequirementsInstalling the HBA into a Computer Recording Reference NumbersRecording the Address and Serial Number Post LED Indicators Verifying the InstallationConfiguration Guidelines for Operating Systems Green LED Yellow LED StateInstallation Page Device Driver Installation IntroductionWindows NT 4.0 System Requirements Installing the Windows NT Scsi Device Driver Verifying the Device Driver Installation Removing the Device DriverShow Adapter / -SET Adapter Commands Tru64Unix Driver and Console SoftwareShow Adapter Command WWIDMGR-SHOW AdapterSET Adapter example OpenVMS Driver and Console Software Page Troubleshooting Post Conditions and ResultsWindows NT Event Viewer HBA Post LED StatesGreen LED Yellow LED Description Windows NT Scsi Port Error Log Windows NT Miniport Event Log CodesExplanation Windows NT Scsi Port Error Log 0x10 Explanation 0x11to 0x13 Further Information OffsetWindows NT Scsi Port Error Log 0x10 Explanation Offset 0xF3 0xF4 HBA reset0x11 to 0x13 Further Information Further Information Parameter Error Values valid only when CmdStat=0x3CmdStat Values 0x12 Offset ExplanationParameter Error Values valid only when CmdStat=0x3 0x12 OffsetWindows NT Scsi Address Mapping Fabric Device MappingBus # Target# Lun# Private Loop Device MappingCurrent Private Loop Device Mapping NoneCurrent Private Loop Device Mapping Current Private Loop Device Mapping Bus # Target# Lun# Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Page Firmware and Diagnostic Utility Diagnostic and Firmware Download UtilityI386 System Installation Starting I386DNLD.EXE in an i386 SystemStarting Alpha Systems with Alpha Bios I386DNLD.EXE Command OptionsOption Description Start-Up for Alpha/i386 Systems Return Diagnostics Main Menu I386DNLD.EXE Main Menu OptionsMenu Selection Modify Test Options MaintenanceTest Host Bus Adapters Restart Host Bus AdaptersDiagnostic and Firmware Loader Utility Show Host Bus Adapter InfoQuit Firmware and Diagnostic Utility Page Using Lputilnt Utility/NT Viewing HBA Parameters Main menu screenPerforming HBA Firmware Maintenance Using the Lputilnt Utility/NTFirmware maintenance screen Upgrading HBA Firmware Deleting or Activating Firmware ImageDownloading PCI Configuration Files Enabling or Disabling Boot BiosModifying Driver Parameters Windows NT Registry Modifying the Driver ParametersDrive Parameters ParameterParameter Description QueueDepth = n QueueTarget = nDrive Parameters AlPA Addresses Page Boot Bios System RequirementsRA8000 or ESA12000 Boot Setup Auto-Configure OptionDisk In-line Exerciser Boot Bios Defining a Fibre Channel Drive as Boot Drive Enabling Boot BiosCreating an MS-DOS Boot Diskette Designating a Fibre Channel Boot Drive on Your ComputerPageUp key Formatting the Fibre Channel Drive on Your Computer Enabling HBA Boot Bios on a Fibre Channel Hard DriveEnabling the Boot Bios PurposePage Installing Windows NT Page Regulatory Compliance Notices FCC Compliance Information Statement Model LP8000-F1 1 XPage Reference Manual Statements for Class B Equipment Federal Communications Commission NoticePage Glossary Page Glossary Page Glossary Page Index Show ADAPTER/-SET AdapterPage Index Page