Compaq LP8000-F1 manual Reference Manual Statements for Class B Equipment

Page 83

Regulatory Compliance Notices A-3

Reference Manual Statements for Class B

Equipment

VCCI

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Any modifications to this device - unless expressly approved by the manufacturer - can void the user’s authority to operate this equipment under part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference that may cause undesirable operation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Image 83
Contents Bit PCI-To-Fibre Channel Host Bus Adapter Page Contents Device Driver Installation Glossary Index List of Figures Text Conventions About This GuideSymbols on Equipment Symbols in TextCompaq Technical Support Getting HelpCompaq Website Compaq Authorized Reseller Product Description IntroductionOverview Bit PCI-to-fibre channel host bus adapter Bit PCI-to-Fibre Channel Host Bus Adapter Jumper SettingsHBA Jumper Settings Jumper Pins Description Device ID CommentsStandards Performance SpecificationsAgency Approvals Page Hardware Requirements InstallationInstallation Overview Software and Documentation Requirements OEMSETUP.INF TXTSETUP.OEM Lpscsi LPUTILNT.EXERecording the Address and Serial Number Installing the HBA into a ComputerRecording Reference Numbers Green LED Yellow LED State Verifying the InstallationConfiguration Guidelines for Operating Systems Post LED IndicatorsInstallation Page Windows NT 4.0 System Requirements Device Driver InstallationIntroduction Installing the Windows NT Scsi Device Driver Removing the Device Driver Verifying the Device Driver InstallationTru64Unix Driver and Console Software Show Adapter / -SET Adapter CommandsWWIDMGR-SHOW Adapter Show Adapter CommandSET Adapter example OpenVMS Driver and Console Software Page Post Conditions and Results TroubleshootingGreen LED Yellow LED Description Windows NT Event ViewerHBA Post LED States Explanation Windows NT Scsi Port Error LogWindows NT Miniport Event Log Codes 0x10 Explanation 0x11to 0x13 Further Information Offset Windows NT Scsi Port Error Log0x11 to 0x13 Further Information Windows NT Scsi Port Error Log 0x10 Explanation Offset 0xF30xF4 HBA reset 0x12 Offset Explanation Parameter Error Values valid only when CmdStat=0x3CmdStat Values Further Information0x12 Offset Parameter Error Values valid only when CmdStat=0x3Fabric Device Mapping Windows NT Scsi Address MappingNone Private Loop Device MappingCurrent Private Loop Device Mapping Bus # Target# Lun#Current Private Loop Device Mapping Current Private Loop Device Mapping Bus # Target# Lun# Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Page Diagnostic and Firmware Download Utility Firmware and Diagnostic UtilityStarting I386DNLD.EXE in an i386 System I386 System InstallationOption Description Starting Alpha Systems with Alpha BiosI386DNLD.EXE Command Options Start-Up for Alpha/i386 Systems Return Menu Selection Diagnostics Main MenuI386DNLD.EXE Main Menu Options Restart Host Bus Adapters MaintenanceTest Host Bus Adapters Modify Test OptionsQuit Diagnostic and Firmware Loader UtilityShow Host Bus Adapter Info Firmware and Diagnostic Utility Page Using Lputilnt Utility/NT Main menu screen Viewing HBA ParametersUsing the Lputilnt Utility/NT Performing HBA Firmware MaintenanceFirmware maintenance screen Deleting or Activating Firmware Image Upgrading HBA FirmwareEnabling or Disabling Boot Bios Downloading PCI Configuration FilesModifying the Driver Parameters Modifying Driver Parameters Windows NT RegistryParameter Drive ParametersQueueDepth = n QueueTarget = n Parameter DescriptionDrive Parameters AlPA Addresses Page System Requirements Boot BiosDisk In-line Exerciser RA8000 or ESA12000 Boot SetupAuto-Configure Option Boot Bios Enabling Boot Bios Defining a Fibre Channel Drive as Boot DriveDesignating a Fibre Channel Boot Drive on Your Computer Creating an MS-DOS Boot DiskettePageUp key Purpose Enabling HBA Boot Bios on a Fibre Channel Hard DriveEnabling the Boot Bios Formatting the Fibre Channel Drive on Your ComputerPage Installing Windows NT Page FCC Compliance Information Statement Model LP8000-F1 1 X Regulatory Compliance NoticesPage Federal Communications Commission Notice Reference Manual Statements for Class B EquipmentPage Glossary Page Glossary Page Glossary Page Show ADAPTER/-SET Adapter IndexPage Index Page