Compaq LP8000-F1 manual Boot Bios

Page 73

Boot BIOS 7-3

Use all defaults and run in read only mode (y/n) [y] ?n Enter execution time limit in minutes (1:65535) [10] ?

Include performance statistics in performance summary (y/n) [n] ? Display hard/soft errors (y/n) [n] ?

Enter IO queue depth (1:8) [4] ?

***Available tests are:

1.Basic function

2.User defined

Use the basic function test 99.9% of the time. The user defined test is for special problems only.

Enter test number (1:2) [1] ?2

In the user defined test, you may define up to 20 commands.

They will be executed in the order entered.

The commands will be repeated until the execution time limit expires.

CAUTION: If you define write commands, user data will be destroyed.

Enter command number 1 (read, write, quit) [] ?write.

Enter data pattern number 0 = ALL, 19 = USER_DEFINED, (0:19) [0] ? Enter starting lbn for this command ?0

Enter the IO size in 512 byte blocks for this command (1:64 [] ?64 Enter command number 2 (read, write, quit) [] ?quit.

Drive unit numbers available for testing on this HBA include: 0.

Enter unit number to be tested ?0. Unit 0 will be write enabled.

Do you wish to add this unit (y/n) [n] ?y. Unit 0 successfully allocated for testing. Maximum number of units are now configured. DILX testing started at : 20:06:34.

Test will run for 10 minutes.

Type ^G to get a current performance summary. Type ^C to terminate the DILX test prematurely. Type ^Y to terminate the DILX prematurely.

DILX terminated prematurely by user request

DILX aborting, abort code 8

HSG BOT3(9600) >

Image 73
Contents Bit PCI-To-Fibre Channel Host Bus Adapter Page Contents Device Driver Installation Glossary Index List of Figures Text Conventions About This GuideSymbols on Equipment Symbols in TextCompaq Technical Support Getting HelpCompaq Website Compaq Authorized Reseller Overview IntroductionProduct Description Bit PCI-to-fibre channel host bus adapter HBA Jumper Settings Jumper SettingsJumper Pins Description Device ID Comments Bit PCI-to-Fibre Channel Host Bus AdapterStandards Performance SpecificationsAgency Approvals Page Installation Overview InstallationHardware Requirements Software and Documentation Requirements OEMSETUP.INF TXTSETUP.OEM Lpscsi LPUTILNT.EXERecording Reference Numbers Installing the HBA into a ComputerRecording the Address and Serial Number Configuration Guidelines for Operating Systems Verifying the InstallationPost LED Indicators Green LED Yellow LED StateInstallation Page Introduction Device Driver InstallationWindows NT 4.0 System Requirements Installing the Windows NT Scsi Device Driver Removing the Device Driver Verifying the Device Driver InstallationTru64Unix Driver and Console Software Show Adapter / -SET Adapter CommandsWWIDMGR-SHOW Adapter Show Adapter CommandSET Adapter example OpenVMS Driver and Console Software Page Post Conditions and Results TroubleshootingHBA Post LED States Windows NT Event ViewerGreen LED Yellow LED Description Windows NT Miniport Event Log Codes Windows NT Scsi Port Error LogExplanation 0x10 Explanation 0x11to 0x13 Further Information Offset Windows NT Scsi Port Error Log0xF4 HBA reset Windows NT Scsi Port Error Log 0x10 Explanation Offset 0xF30x11 to 0x13 Further Information CmdStat Values Parameter Error Values valid only when CmdStat=0x3Further Information 0x12 Offset Explanation0x12 Offset Parameter Error Values valid only when CmdStat=0x3Fabric Device Mapping Windows NT Scsi Address MappingCurrent Private Loop Device Mapping Private Loop Device MappingBus # Target# Lun# NoneCurrent Private Loop Device Mapping Current Private Loop Device Mapping Bus # Target# Lun# Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Page Diagnostic and Firmware Download Utility Firmware and Diagnostic UtilityStarting I386DNLD.EXE in an i386 System I386 System InstallationI386DNLD.EXE Command Options Starting Alpha Systems with Alpha BiosOption Description Start-Up for Alpha/i386 Systems Return I386DNLD.EXE Main Menu Options Diagnostics Main MenuMenu Selection Test Host Bus Adapters MaintenanceModify Test Options Restart Host Bus AdaptersShow Host Bus Adapter Info Diagnostic and Firmware Loader UtilityQuit Firmware and Diagnostic Utility Page Using Lputilnt Utility/NT Main menu screen Viewing HBA ParametersUsing the Lputilnt Utility/NT Performing HBA Firmware MaintenanceFirmware maintenance screen Deleting or Activating Firmware Image Upgrading HBA FirmwareEnabling or Disabling Boot Bios Downloading PCI Configuration FilesModifying the Driver Parameters Modifying Driver Parameters Windows NT RegistryParameter Drive ParametersQueueDepth = n QueueTarget = n Parameter DescriptionDrive Parameters AlPA Addresses Page System Requirements Boot BiosAuto-Configure Option RA8000 or ESA12000 Boot SetupDisk In-line Exerciser Boot Bios Enabling Boot Bios Defining a Fibre Channel Drive as Boot DriveDesignating a Fibre Channel Boot Drive on Your Computer Creating an MS-DOS Boot DiskettePageUp key Enabling the Boot Bios Enabling HBA Boot Bios on a Fibre Channel Hard DriveFormatting the Fibre Channel Drive on Your Computer PurposePage Installing Windows NT Page FCC Compliance Information Statement Model LP8000-F1 1 X Regulatory Compliance NoticesPage Federal Communications Commission Notice Reference Manual Statements for Class B EquipmentPage Glossary Page Glossary Page Glossary Page Show ADAPTER/-SET Adapter IndexPage Index Page