Compaq LP8000-F1 manual Glossary Index

Page 5

 

About This Guide v

Chapter 6

 

Using LPUTILNT Utility/NT

 

Introduction

6-1

Viewing HBA Parameters

6-2

Performing HBA Firmware Maintenance

6-3

Upgrading HBA Firmware

6-5

Deleting or Activating Firmware Image

6-5

Enabling or Disabling Boot BIOS

6-6

Downloading PCI Configuration Files

6-6

Modifying Driver Parameters in the Windows NT Registry

6-7

Chapter 7

 

Boot BIOS

 

Introduction

7-1

System Requirements

7-1

RA8000 or ESA12000 Boot Setup

7-2

Disk In-line Exerciser

7-2

The Auto-Configure Option

7-2

Defining a Fibre Channel Drive as the Boot Drive

7-4

Enabling Boot BIOS

7-4

Creating an MS-DOS Boot Diskette

7-5

Designating a Fibre Channel Boot Drive on Your Computer

7-5

Formatting the Fibre Channel Drive on Your Computer

7-7

Enabling HBA Boot BIOS on a Fibre Channel Hard Drive

7-7

Installing Windows NT

7-9

Appendix A

 

Regulatory Compliance Notices

 

FCC Compliance Information Statement Model LP8000-F1 (1 X 9)

A-1

Reference Manual Statements for Class B Equipment

A-3

VCCI

A-3

Federal Communications Commission Notice

A-3

Glossary

Index

Image 5
Contents Bit PCI-To-Fibre Channel Host Bus Adapter Page Contents Device Driver Installation Glossary Index List of Figures Text Conventions About This GuideSymbols on Equipment Symbols in TextCompaq Technical Support Getting HelpCompaq Website Compaq Authorized Reseller Product Description IntroductionOverview Bit PCI-to-fibre channel host bus adapter HBA Jumper Settings Jumper SettingsJumper Pins Description Device ID Comments Bit PCI-to-Fibre Channel Host Bus AdapterStandards Performance SpecificationsAgency Approvals Page Hardware Requirements InstallationInstallation Overview Software and Documentation Requirements OEMSETUP.INF TXTSETUP.OEM Lpscsi LPUTILNT.EXERecording the Address and Serial Number Installing the HBA into a ComputerRecording Reference Numbers Configuration Guidelines for Operating Systems Verifying the InstallationPost LED Indicators Green LED Yellow LED StateInstallation Page Windows NT 4.0 System Requirements Device Driver InstallationIntroduction Installing the Windows NT Scsi Device Driver Removing the Device Driver Verifying the Device Driver InstallationTru64Unix Driver and Console Software Show Adapter / -SET Adapter CommandsWWIDMGR-SHOW Adapter Show Adapter CommandSET Adapter example OpenVMS Driver and Console Software Page Post Conditions and Results TroubleshootingGreen LED Yellow LED Description Windows NT Event ViewerHBA Post LED States Explanation Windows NT Scsi Port Error LogWindows NT Miniport Event Log Codes 0x10 Explanation 0x11to 0x13 Further Information Offset Windows NT Scsi Port Error Log0x11 to 0x13 Further Information Windows NT Scsi Port Error Log 0x10 Explanation Offset 0xF30xF4 HBA reset CmdStat Values Parameter Error Values valid only when CmdStat=0x3Further Information 0x12 Offset Explanation0x12 Offset Parameter Error Values valid only when CmdStat=0x3Fabric Device Mapping Windows NT Scsi Address MappingCurrent Private Loop Device Mapping Private Loop Device MappingBus # Target# Lun# NoneCurrent Private Loop Device Mapping Current Private Loop Device Mapping Bus # Target# Lun# Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Current Private Loop Device Mapping Alpa Selid Page Diagnostic and Firmware Download Utility Firmware and Diagnostic UtilityStarting I386DNLD.EXE in an i386 System I386 System InstallationOption Description Starting Alpha Systems with Alpha BiosI386DNLD.EXE Command Options Start-Up for Alpha/i386 Systems Return Menu Selection Diagnostics Main MenuI386DNLD.EXE Main Menu Options Test Host Bus Adapters MaintenanceModify Test Options Restart Host Bus AdaptersQuit Diagnostic and Firmware Loader UtilityShow Host Bus Adapter Info Firmware and Diagnostic Utility Page Using Lputilnt Utility/NT Main menu screen Viewing HBA ParametersUsing the Lputilnt Utility/NT Performing HBA Firmware MaintenanceFirmware maintenance screen Deleting or Activating Firmware Image Upgrading HBA FirmwareEnabling or Disabling Boot Bios Downloading PCI Configuration FilesModifying the Driver Parameters Modifying Driver Parameters Windows NT RegistryParameter Drive ParametersQueueDepth = n QueueTarget = n Parameter DescriptionDrive Parameters AlPA Addresses Page System Requirements Boot BiosDisk In-line Exerciser RA8000 or ESA12000 Boot SetupAuto-Configure Option Boot Bios Enabling Boot Bios Defining a Fibre Channel Drive as Boot DriveDesignating a Fibre Channel Boot Drive on Your Computer Creating an MS-DOS Boot DiskettePageUp key Enabling the Boot Bios Enabling HBA Boot Bios on a Fibre Channel Hard DriveFormatting the Fibre Channel Drive on Your Computer PurposePage Installing Windows NT Page FCC Compliance Information Statement Model LP8000-F1 1 X Regulatory Compliance NoticesPage Federal Communications Commission Notice Reference Manual Statements for Class B EquipmentPage Glossary Page Glossary Page Glossary Page Show ADAPTER/-SET Adapter IndexPage Index Page