Apple CP-X2021WN Indicator Indicator indicator, At least 1 Power on schedule is saved to, Guide

Page 101

Troubleshooting

Regarding the indicator lamps (continued)

POWER

LAMP TEMP

Description

indicator

indicator indicator

 

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

 

 

 

Please turn the power off, and allow the projector to

 

 

 

cool down at least 20 minutes. After the projector has

Blinking

 

 

sufficiently cooled down, please make confirmation of

 

 

the following items, and then turn the power on again.

In Red

Turned

Lighting

• Is there blockage of the air passage aperture?

or

off

In Red

• Is the air filter dirty?

Lighting

 

 

• Does the peripheral temperature exceed 35°C?

In Red

 

 

 

 

• If the projector is used at an altitude of about 1600 m

 

 

 

 

 

 

(5250 feet) or higher, set ALTITUDE of the SERVICE

 

 

 

item in the OPTION menu to HIGH (￿57). If the

 

 

 

projector is used with a wrong setting, it may cause

 

 

 

damage to the projector itself or the parts inside.

 

 

It is time to clean the air filter.

 

 

Please immediately turn the power off, and clean or

Lighting

Simultaneous

change the air filter referring to the section Cleaning

In Green

blinking in Red

and replacing the air filter. After cleaning or changing

 

 

the air filter, please be sure to reset the filter timer.

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

 

 

 

After the treatment, reset the power to ON.

 

 

 

 

Blinking In

 

 

At least 1 Power ON schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

Please refer to Schedule Settings in the Network

seconds.

 

 

Guide.

NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again. If the projector is used at an altitude of about 1600 m (5250 feet) or higher, set ALTITUDE of the SERVICE item in the OPTION menu to HIGH (￿57). Otherwise, set it to NORMAL.

101

Page 100 Page 102
Image 101
Page 100 Page 102
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Checking the contents of package FeaturesHOT Part namesSTANDBY/ON button Control panelRear panel 11 ~ Computer button Remote controlDown button Volume + button Arrangement Setting upArrangement Arrangement About Plug-and-Play capability Connecting with your devicesComputer Connecting with your devicesWireless adapter optional Computer External device Access PointUSB Storage DeviceVCR/DVD/Blu-ray DiscTM player Monitor SpeakersConnecting to a power supply Using the security bar and slot Installing the batteries Remote controlAbout the remote control signal Hitachi Maxell or Hitachi MaxellUsing as a simple PC mouse & keyboard STANDBY/ON button Power indicator Power on/offTurning on the power Precaution for lens cover attachment and removal Turning off the powerVolume +/- button Adjusting the volumeOperating Temporarily muting the soundMY Source Selecting an input signalFor an Hdmitm signal Searching an input signalSelecting an aspect ratio Search buttonAdjusting the zoom and focus Adjusting the projectors elevatorZoom ring Focus ringAdjusting the position Using the automatic adjustment featureKeystone button Correcting the keystone distortionsMagnify ON/OFF button Using the magnify featureTemporarily blanking the screen Temporarily freezing the screenFreeze button Blank buttonAdvanced Menu Using the menu functionEasy Menu Indication Meaning Indication in OSD On Screen DisplayDescription Picture ModeAspect Auto KeystoneInstallation ECO ModeReset Filter TimeBrightness Picture menuContrast GammaColor Temp CustomColor TintMY Memory LOAD-1,LOAD-2,LOAD-3,LOAD-4 SharpnessSAVE-1, SAVE-2, SAVE-3, SAVE-4 Image menu For a computer signalFor an Hdmitm signal USB Type B or Hdmi port PositionAuto Adjust PhaseSize ExecuteTV Film OFF Input menuHigh MID LOW Video NRHdmi Range Video FormatHdmi Format Auto Sync on G OFF ComputerFrame Lock On OFFResolution Setup menu ECO Intelligent ECO Normal Auto ECO ModeMonitor OUT Standby ModeNormal Saving Audio menu VolumeSpeaker Audio SourceEnglish Français Deutsch Español Screen menuBlank Start UPMyScreen registration is finished Capturing error has occurred. Please try againDescription MyScreen No Input is Detected MyScreen LockSync is OUT of Range Invalid Scan FreqSource Name Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3 TemplateDisplay Description Closed CaptionMode ChannelOption menu Direct PowerAuto Search USB Type B portOFF Auto PowerMouse USB Display USB Type BAir filter Cancel OKLamp Time MY Button Altitude ServiceGhost Control Panel Remote ControlFilter Message KEY LockCommunication Type Commands Network Bridge FunctionNetwork Guide Control port Serial SettingsBaud Rate ParityTransmission Method 59 Response Limit TimeInformation Factory ResetAdhoc Infrastructure Wireless SetupNetwork menu Dhcp DefaultIP Address SubnetDate WirelessWPA2-PSKAES WPA2-PSKTKIP OFF WPA-PSKAES#1 Default #2 Default #3 Default Wireless Setup SsidWireless Information Wired Setup Wired Information Projector Name AMX D.D MY ImagePresentation QuitUser Name Multi PCSecurity menu PasswordEnter to the Security menu SecurityMyScreen Turning on the MyScreen PasswordTurning off the MyScreen Password Turning on the PIN Lock PIN LockTurning off the PIN Lock If you have forgotten your PIN codeTurning off the Transition Detector Transition DetectorTurning on the Transition Detector Turning off the MY Text Password MY Text PasswordTurning on the MY Text Password Writing MY TextPC-LESS Presentation Presentation toolsSupported storage media Supported formatSupported file format and its extension PC-LESS PresentationOperating by buttons or keys Setup menu for the selected imageButton operation Down Enter InputOperating by the menu on the Thumbnail screen PC-LESS Presentation Button operation Functions Operations for still imagesDown Enter InputSlideshow Mode Return Example of playlist.txt files PlaylistUSB Port USB cable 1 piece USB DisplayHardware and software requirement for computer USB Display Right-Click menu Optimize Performance Keep PC resolutionTransmission speed Image qualityType number DT01191 Replacing the lamp MaintenanceReplacing the lamp Lamp warning High Voltage High Temperature High PressureType number UX36761 Filter set Cleaning and replacing the air filterCleaning and replacing the air filter Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensThere is no input signal TroubleshootingAn improper signal is input Related messagesButton operation is not available Internal temperature is risingPower Lamp Temp Regarding the indicator lampsAt least 1 Power on schedule is saved to Indicator Indicator indicatorOff Please refer to Schedule Settings in the Network ProjectorPhenomenon Cases not involving a machine defect Resetting all settingsUSB Type B port is selected as the picture input Audio SOURCE/SPEAKER setting is not correctBrightness is adjusted to an extremely low level Freeze function is working Network USB TypeDisconnect the LAN cable and check that the projector Phenomenon Cases not involving a machine defect ReferenceEnd User License Agreement for the Projector Software Specifications
Top Page Image Contents