Apple CP-X2521WN Resetting all settings, Phenomenon Cases not involving a machine defect

Page 102

Troubleshooting

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (￿62) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and

NETWORK) to the factory default. Be sure to set ALTITUDE after resetting all the settings (￿57).

Phenomena that may be easy to be mistaken for machine defects

About the phenomenon confused with a machine defect, check and cope with it according to the following table.

Phenomenon

Cases not involving a machine defect

Reference

page

 

 

 

The electrical power cord is not plugged in.

15

 

Correctly connect the power cord.

 

 

 

The main power source has been interrupted during

 

 

operation such as by a power outage (blackout), etc.

15

 

Please disconnect the power plug from the power outlet,

 

and allow the projector to cool down at least 10 minutes,

 

Power does

then turn the power on again.

 

not come on.

Either there is no lamp and/or lamp cover, or either

 

 

of these has not been properly fixed.

 

 

Please turn the power off and disconnect the power

 

 

plug from the power outlet, and allow the projector to

93

 

cool down at least 45 minutes. After the projector has

 

 

 

sufficiently cooled down, please make confirmation of

 

 

the attachment state of the lamp and lamp cover, and

 

 

then turn the power on again.

 

 

The signal cables are not correctly connected.

10 ~ 14

 

Correctly connect the connection cables.

 

 

 

Signal source does not correctly work.

 

Correctly set up the signal source device by referring to

 

the manual of the source device.

 

Neither sounds

The input changeover settings are mismatched.

21 ~ 23

nor pictures are

Select the input signal, and correct the settings.

 

outputted.

 

 

The BLANK function for pictures and the MUTE

 

 

 

 

function for sounds are working.

 

 

AV MUTE may be active.

28, 57,

 

Refer to the item “Sound does not come out” and “No

103

 

pictures are displayed” on the next page to turn off the

 

 

MUTE and BLANK functions.

 

(continued on next page)

 

102

Image 102
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Features Checking the contents of packagePart names HOTControl panel Rear panel 11 ~STANDBY/ON button Remote control Down button Volume + buttonComputer button Setting up ArrangementArrangement Arrangement Connecting with your devices About Plug-and-Play capabilityConnecting with your devices ComputerUSB Computer External device Access PointWireless adapter optional Storage DeviceVCR/DVD/Blu-ray DiscTM player Speakers MonitorConnecting to a power supply Using the security bar and slot About the remote control signal Remote controlInstalling the batteries Hitachi Maxell or Hitachi MaxellUsing as a simple PC mouse & keyboard Power on/off Turning on the powerSTANDBY/ON button Power indicator Turning off the power Precaution for lens cover attachment and removalOperating Adjusting the volumeVolume +/- button Temporarily muting the soundSelecting an input signal MY SourceSelecting an aspect ratio Searching an input signalFor an Hdmitm signal Search buttonZoom ring Adjusting the projectors elevatorAdjusting the zoom and focus Focus ringUsing the automatic adjustment feature Adjusting the positionCorrecting the keystone distortions Keystone buttonUsing the magnify feature Magnify ON/OFF buttonFreeze button Temporarily freezing the screenTemporarily blanking the screen Blank buttonUsing the menu function Easy MenuAdvanced Menu Indication in OSD On Screen Display Indication MeaningAspect Picture ModeDescription Auto KeystoneReset ECO ModeInstallation Filter TimeContrast Picture menuBrightness GammaColor CustomColor Temp TintSharpness SAVE-1, SAVE-2, SAVE-3, SAVE-4MY Memory LOAD-1,LOAD-2,LOAD-3,LOAD-4 For a computer signal For an Hdmitm signalImage menu Position USB Type B or Hdmi portSize PhaseAuto Adjust ExecuteHigh MID LOW Input menuTV Film OFF Video NRVideo Format Hdmi FormatHdmi Range Frame Lock ComputerAuto Sync on G OFF On OFFResolution Setup menu Auto ECO Mode ECO Intelligent ECO NormalStandby Mode Normal SavingMonitor OUT Speaker VolumeAudio menu Audio SourceBlank Screen menuEnglish Français Deutsch Español Start UPCapturing error has occurred. Please try again Description MyScreenMyScreen registration is finished Sync is OUT of Range MyScreen LockNo Input is Detected Invalid Scan FreqSource Name Template Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3Mode Description Closed CaptionDisplay ChannelAuto Search Direct PowerOption menu USB Type B portMouse USB Display Auto PowerOFF USB Type BCancel OK Lamp TimeAir filter MY Button Service AltitudeFilter Message Control Panel Remote ControlGhost KEY LockCommands Network Bridge Function Network GuideCommunication Type Baud Rate Serial SettingsControl port ParityResponse Limit Time Transmission Method 59Factory Reset InformationWireless Setup Network menuAdhoc Infrastructure IP Address DefaultDhcp SubnetWPA2-PSKAES WPA2-PSKTKIP WirelessDate OFF WPA-PSKAESWireless Setup Ssid #1 Default #2 Default #3 DefaultWireless Information Wired Setup Wired Information Projector Name MY Image AMX D.DQuit PresentationMulti PC User NameEnter to the Security menu PasswordSecurity menu SecurityTurning on the MyScreen Password Turning off the MyScreen PasswordMyScreen Turning off the PIN Lock PIN LockTurning on the PIN Lock If you have forgotten your PIN codeTransition Detector Turning on the Transition DetectorTurning off the Transition Detector MY Text Password Turning on the MY Text PasswordTurning off the MY Text Password MY Text WritingSupported storage media Presentation toolsPC-LESS Presentation Supported formatPC-LESS Presentation Supported file format and its extensionButton operation Setup menu for the selected imageOperating by buttons or keys Down Enter InputOperating by the menu on the Thumbnail screen PC-LESS Presentation Down Operations for still imagesButton operation Functions Enter InputSlideshow Mode Return Playlist Example of playlist.txt filesUSB Display Hardware and software requirement for computerUSB Port USB cable 1 piece USB Display Right-Click menu Transmission speed Keep PC resolutionOptimize Performance Image qualityMaintenance Replacing the lampType number DT01191 Replacing the lamp High Voltage High Temperature High Pressure Lamp warningCleaning and replacing the air filter Type number UX36761 Filter setCleaning and replacing the air filter Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensAn improper signal is input TroubleshootingThere is no input signal Related messagesInternal temperature is rising Button operation is not availableRegarding the indicator lamps Power Lamp TempOff Please refer to Schedule Settings in the Network Indicator Indicator indicatorAt least 1 Power on schedule is saved to ProjectorResetting all settings Phenomenon Cases not involving a machine defectAudio SOURCE/SPEAKER setting is not correct Brightness is adjusted to an extremely low levelUSB Type B port is selected as the picture input Freeze function is working USB Type NetworkPhenomenon Cases not involving a machine defect Reference Disconnect the LAN cable and check that the projectorSpecifications End User License Agreement for the Projector Software