Apple CP-X2021WN, CP-X2521WN, CP-X3021WN Enter to the Security menu, Password, Change

Page 74

SECURITY menu

SECURITY menu

This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed.

To use SECURITY menu: User registration is required before using the security functions.

Enter to the SECURITY menu

1.Press the ► button. The ENTER PASSWORD box will be displayed.

2.Use the ▲/▼/◄/► buttons to enter the registered password. The factory default password is as follows.

3692

This password can be changed (below). Move the cursor to the right side of the ENTER PASSWORD box and press

the ► button to display the SECURITY menu.

•It is strongly recommended the factory default password to be changed as soon as possible.

•If an incorrect password is input, the ENTER PASSWORD box will be displayed again. If incorrect password is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.

3.Items shown in the table below can be performed.

If you have forgotten your password

(1)While the ENTER PASSWORD box is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector.

(2)The 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is conﬁrmed.

•If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will close. If necessary, repeat the process from (1).

Item		Description

	(1)	Use the ▲/▼ buttons on the SECURITY menu
		to select SECURITY PASSWORD CHANGE
		and press the ► button to display the ENTER
		NEW PASSWORD box.
	(2)	Use the ▲/▼/◄/► buttons to enter the new password.
	(3)	Move the cursor to the right side of the
SECURITY		ENTER NEW PASSWORD box and press the
SECURITY		► button to display the NEW PASSWORD
PASSWORD		AGAIN box, enter the same password again.
CHANGE	(4) Move the cursor to the right side of the NEW
		PASSWORD AGAIN box and press the ►
		button and the NOTE NEW PASSWORD box
		will be displayed for about 30 seconds, please
		make note of the password during this time.
		Pressing the ENTER button on the remote control or ► button on the
		projector will close the NOTE NEW PASSWORD box.
	• Please do not forget your password.

(continued on next page)

74

Image 74

Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents Features Checking the contents of packagePart names HOTSTANDBY/ON button Control panelRear panel 11 ~ Computer button Remote controlDown button Volume + button Setting up ArrangementArrangement Arrangement Connecting with your devices About Plug-and-Play capabilityConnecting with your devices ComputerUSB Computer External device Access PointWireless adapter optional Storage DeviceVCR/DVD/Blu-ray DiscTM player Speakers MonitorConnecting to a power supply Using the security bar and slot About the remote control signal Remote controlInstalling the batteries Hitachi Maxell or Hitachi MaxellUsing as a simple PC mouse & keyboard STANDBY/ON button Power indicator Power on/offTurning on the power Turning off the power Precaution for lens cover attachment and removalOperating Adjusting the volumeVolume +/- button Temporarily muting the soundSelecting an input signal MY SourceSelecting an aspect ratio Searching an input signalFor an Hdmitm signal Search buttonZoom ring Adjusting the projectors elevatorAdjusting the zoom and focus Focus ringUsing the automatic adjustment feature Adjusting the positionCorrecting the keystone distortions Keystone buttonUsing the magnify feature Magnify ON/OFF buttonFreeze button Temporarily freezing the screenTemporarily blanking the screen Blank buttonAdvanced Menu Using the menu functionEasy Menu Indication in OSD On Screen Display Indication MeaningAspect Picture ModeDescription Auto KeystoneReset ECO ModeInstallation Filter TimeContrast Picture menuBrightness GammaColor CustomColor Temp TintMY Memory LOAD-1,LOAD-2,LOAD-3,LOAD-4 SharpnessSAVE-1, SAVE-2, SAVE-3, SAVE-4 Image menu For a computer signalFor an Hdmitm signal Position USB Type B or Hdmi portSize PhaseAuto Adjust ExecuteHigh MID LOW Input menuTV Film OFF Video NRHdmi Range Video FormatHdmi Format Frame Lock ComputerAuto Sync on G OFF On OFFResolution Setup menu Auto ECO Mode ECO Intelligent ECO NormalMonitor OUT Standby ModeNormal Saving Speaker VolumeAudio menu Audio SourceBlank Screen menuEnglish Français Deutsch Español Start UPMyScreen registration is ﬁnished Capturing error has occurred. Please try againDescription MyScreen Sync is OUT of Range MyScreen LockNo Input is Detected Invalid Scan FreqSource Name Template Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3Mode Description Closed CaptionDisplay ChannelAuto Search Direct PowerOption menu USB Type B portMouse USB Display Auto PowerOFF USB Type BAir ﬁlter Cancel OKLamp Time MY Button Service AltitudeFilter Message Control Panel Remote ControlGhost KEY LockCommunication Type Commands Network Bridge FunctionNetwork Guide Baud Rate Serial SettingsControl port ParityResponse Limit Time Transmission Method 59Factory Reset InformationAdhoc Infrastructure Wireless SetupNetwork menu IP Address DefaultDhcp SubnetWPA2-PSKAES WPA2-PSKTKIP WirelessDate OFF WPA-PSKAESWireless Setup Ssid #1 Default #2 Default #3 DefaultWireless Information Wired Setup Wired Information Projector Name MY Image AMX D.DQuit PresentationMulti PC User NameEnter to the Security menu PasswordSecurity menu SecurityMyScreen Turning on the MyScreen PasswordTurning off the MyScreen Password Turning off the PIN Lock PIN LockTurning on the PIN Lock If you have forgotten your PIN codeTurning off the Transition Detector Transition DetectorTurning on the Transition Detector Turning off the MY Text Password MY Text PasswordTurning on the MY Text Password MY Text WritingSupported storage media Presentation toolsPC-LESS Presentation Supported formatPC-LESS Presentation Supported ﬁle format and its extensionButton operation Setup menu for the selected imageOperating by buttons or keys Down Enter InputOperating by the menu on the Thumbnail screen PC-LESS Presentation Down Operations for still imagesButton operation Functions Enter InputSlideshow Mode Return Playlist Example of playlist.txt ﬁlesUSB Port USB cable 1 piece USB DisplayHardware and software requirement for computer USB Display Right-Click menu Transmission speed Keep PC resolutionOptimize Performance Image qualityType number DT01191 Replacing the lamp MaintenanceReplacing the lamp High Voltage High Temperature High Pressure Lamp warningCleaning and replacing the air ﬁlter Type number UX36761 Filter setCleaning and replacing the air ﬁlter Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensAn improper signal is input TroubleshootingThere is no input signal Related messagesInternal temperature is rising Button operation is not availableRegarding the indicator lamps Power Lamp TempOff Please refer to Schedule Settings in the Network Indicator Indicator indicatorAt least 1 Power on schedule is saved to ProjectorResetting all settings Phenomenon Cases not involving a machine defectUSB Type B port is selected as the picture input Audio SOURCE/SPEAKER setting is not correctBrightness is adjusted to an extremely low level Freeze function is working USB Type NetworkPhenomenon Cases not involving a machine defect Reference Disconnect the LAN cable and check that the projectorSpeciﬁcations End User License Agreement for the Projector Software