Apple CP-X2521WN, CP-X3021WN, CP-X2021WN Network menu, Wireless Setup, Adhoc Infrastructure

Page 63

NETWORK menu

NETWORK menu

Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network. Select “NETWORK” from the main menu to access the following functions.

Select an item using the ▲/▼ cursor buttons on the

projector or remote control, and press the ► cursor button on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. See the Network Guide for details of NETWORK operation.

NOTE • To use the wireless network function of this projector, the designated USB wireless adapter that is sold as an option is required. Do not use

any extension cable or device when connecting the adapter to the projector.

•The projector does not allow both wireless and wired LAN to be connected to the same network.

•Do not set the same network address for both wireless and wired LAN.

•If you are not utilizing SNTP (Date/Time Settings in the Network Guide), then you must set the DATE AND TIME during the initial installation.

•The network communication control is disabled while the projector is in standby mode if the STANDBY MODE item of SETUP menu is set to SAVING.

Please connect the network communication to the projector after setting the STANDBY MODE to NORMAL (45).

Item

Description

WIRELESS

SETUP

Selecting this item displays the WIRELESS SETUP menu for the wireless LAN.

Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item.

		Use the ▲/▼ buttons to select the mode of the
		network communication system. Select according
		to the settings of your computer.
		ADHOC INFRASTRUCTURE
	MODE	To save the setting, press the ► button.
	MODE	• When ADHOC is selected, IEEE802.11 n cannot
		• When ADHOC is selected, IEEE802.11 n cannot
		be used.
		• If ADHOC is set to MODE while one of WPA-
		PSK or WPA2-PSK is selected in ENCRYPTION,
		the ENCRYPTION (65) setting switches to OFF
		automatically.

(continued on next page)

63

Image 63

Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Contents Checking the contents of package FeaturesHOT Part namesControl panel Rear panel 11 ~STANDBY/ON button Remote control Down button Volume + buttonComputer button Arrangement Setting upArrangement Arrangement About Plug-and-Play capability Connecting with your devicesComputer Connecting with your devicesStorage Device Computer External device Access PointWireless adapter optional USBVCR/DVD/Blu-ray DiscTM player Monitor SpeakersConnecting to a power supply Using the security bar and slot Hitachi Maxell or Hitachi Maxell Remote controlInstalling the batteries About the remote control signalUsing as a simple PC mouse & keyboard Power on/off Turning on the powerSTANDBY/ON button Power indicator Precaution for lens cover attachment and removal Turning off the powerTemporarily muting the sound Adjusting the volumeVolume +/- button OperatingMY Source Selecting an input signalSearch button Searching an input signalFor an Hdmitm signal Selecting an aspect ratioFocus ring Adjusting the projectors elevatorAdjusting the zoom and focus Zoom ringAdjusting the position Using the automatic adjustment featureKeystone button Correcting the keystone distortionsMagnify ON/OFF button Using the magnify featureBlank button Temporarily freezing the screenTemporarily blanking the screen Freeze buttonUsing the menu function Easy MenuAdvanced Menu Indication Meaning Indication in OSD On Screen DisplayAuto Keystone Picture ModeDescription AspectFilter Time ECO ModeInstallation ResetGamma Picture menuBrightness ContrastTint CustomColor Temp ColorSharpness SAVE-1, SAVE-2, SAVE-3, SAVE-4MY Memory LOAD-1,LOAD-2,LOAD-3,LOAD-4 For a computer signal For an Hdmitm signalImage menu USB Type B or Hdmi port PositionExecute PhaseAuto Adjust SizeVideo NR Input menuTV Film OFF High MID LOWVideo Format Hdmi FormatHdmi Range On OFF ComputerAuto Sync on G OFF Frame LockResolution Setup menu ECO Intelligent ECO Normal Auto ECO ModeStandby Mode Normal SavingMonitor OUT Audio Source VolumeAudio menu SpeakerStart UP Screen menuEnglish Français Deutsch Español BlankCapturing error has occurred. Please try again Description MyScreenMyScreen registration is ﬁnished Invalid Scan Freq MyScreen LockNo Input is Detected Sync is OUT of RangeSource Name Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3 TemplateChannel Description Closed CaptionDisplay ModeUSB Type B port Direct PowerOption menu Auto SearchUSB Type B Auto PowerOFF Mouse USB DisplayCancel OK Lamp TimeAir ﬁlter MY Button Altitude ServiceKEY Lock Control Panel Remote ControlGhost Filter MessageCommands Network Bridge Function Network GuideCommunication Type Parity Serial SettingsControl port Baud RateTransmission Method 59 Response Limit TimeInformation Factory ResetWireless Setup Network menuAdhoc Infrastructure Subnet DefaultDhcp IP AddressOFF WPA-PSKAES WirelessDate WPA2-PSKAES WPA2-PSKTKIP#1 Default #2 Default #3 Default Wireless Setup SsidWireless Information Wired Setup Wired Information Projector Name AMX D.D MY ImagePresentation QuitUser Name Multi PCSecurity PasswordSecurity menu Enter to the Security menuTurning on the MyScreen Password Turning off the MyScreen PasswordMyScreen If you have forgotten your PIN code PIN LockTurning on the PIN Lock Turning off the PIN LockTransition Detector Turning on the Transition DetectorTurning off the Transition Detector MY Text Password Turning on the MY Text PasswordTurning off the MY Text Password Writing MY TextSupported format Presentation toolsPC-LESS Presentation Supported storage mediaSupported ﬁle format and its extension PC-LESS PresentationDown Enter Input Setup menu for the selected imageOperating by buttons or keys Button operationOperating by the menu on the Thumbnail screen PC-LESS Presentation Enter Input Operations for still imagesButton operation Functions DownSlideshow Mode Return Example of playlist.txt ﬁles PlaylistUSB Display Hardware and software requirement for computerUSB Port USB cable 1 piece USB Display Right-Click menu Image quality Keep PC resolutionOptimize Performance Transmission speedMaintenance Replacing the lampType number DT01191 Replacing the lamp Lamp warning High Voltage High Temperature High PressureType number UX36761 Filter set Cleaning and replacing the air ﬁlterCleaning and replacing the air ﬁlter Caring for the lens Caring for the cabinet and remote controlOther care Inside of the projectorRelated messages TroubleshootingThere is no input signal An improper signal is inputButton operation is not available Internal temperature is risingPower Lamp Temp Regarding the indicator lampsProjector Indicator Indicator indicatorAt least 1 Power on schedule is saved to Off Please refer to Schedule Settings in the NetworkPhenomenon Cases not involving a machine defect Resetting all settingsAudio SOURCE/SPEAKER setting is not correct Brightness is adjusted to an extremely low levelUSB Type B port is selected as the picture input Freeze function is working Network USB TypeDisconnect the LAN cable and check that the projector Phenomenon Cases not involving a machine defect ReferenceEnd User License Agreement for the Projector Software Speciﬁcations