Barco R9001390 manual Installation, Configuration OSD Color, Front/Table

Page 13

Installation Set Up

5HDU4&HLOLQJ	INSTALLATION SET)URQWUP&HLOLQJ
The projector can be installed to project images in four different
configurations5HDU7DEOH	: front/table, front/ceiling, rear/table and rear/ceiling.	)URWQ7DEOH

To change the Configuration, enter the adjustment mode by pushing ADJUST or ENTER. Highlight Installation by pushing the control disc forward or backward and press ENTER to select. The installation menu will be displayed.

ENTER displays the Installation menu.

EXIT or ADJUST returns to operational mode.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

Highlight Configuration by pushing the control disc forward or backward and press ENTER to select. The configuration menu will be displayed.

ENTER displays the Configuration menu.

EXIT returns to the path selection menu.

ADJUST returns to operational mode.

The actual selected configuration will be highlighted.

Push the control disc forward or backward to select the corresponding configuration with regard to the projector environment. Press ENTER to confirm your selection.

ENTER to confirm the selection.

EXIT returns to the installation menu.

ADJUST returns to operational mode.

INSTALLATION

INPUT SLOTS

800PERIPHERAL

CONVERGENCE

CONFIGURATION OSD COLOR

INTERNAL PATTERNS

Select with or then <ENTER> <EXIT> to return.

CONFIGURATION

FRONT/TABLE

FRONT/CEILING

REAR/TABLE

REAR/CEILING

Select with or then <ENTER> <EXIT> to return.

5975938 BARCOREALITY 9200TCR+ 020798		4-1

Image 13

Contents Reality 9200 TCR+ Page Date Art. No 020798 R5975938 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 10-1 Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?Componentvideo Separate SyncFront Panel Terminology Location and Functions of ControlControl Panel Terminology a. Local keypad RCU Remote controlConfiguration OSD Color InstallationFRONT/TABLE Installation Set Up Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byLamp Run Time Input ConnectionsFixed RGB analog input slot Periphiral Convergence Configuration Input SlotsEnter Input SlotsFixed 5-Input Slot slot Peripheral Convergence ConfigurationRgbhv Rgbs Video269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module Component Input Module Guided Random Access2032117B-Y S9,2,1387 RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting a Rcvds 05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorControlling How to Use the RCU?Projector Address How to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access BrightnessAdjustment Mode Start UP of the Adjustment ModeRandom Access Installation Service PasswordStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Load File File ServiceEdit File LoadPeriod Horizontal Total Pixels ActiveVertical Field Total LinesConfirm Edit File Edit File OptionsCopy RenameRename CopyDelete Picture TuningFile Options CTI ON/OFFStill Video Color TemperatureCTI on Still Video onDecoding EBU/IRE GammaDynamic Color Depth Noise ReductionGeometry Edge EnhancementShift GeometrySide Keystone SizeSize Side KeystoneOptions BlankingBlanking Random Access Adjustment Mode Input Slots Starting up the Installation ModeTroubleshooting How to AdjustPeripheral ConvergenceGreen to Midposition Green FocusingBlue on Green convergence Hatch Red on Green convergenceAbout Moca No Signal BLACK/BLUE ConfigurationOSD color On-Screen Display Internal PatternsInstallation Mode Starting up the Service Mode Service ModeService Identification IdentificationHow to enable or disable the password function ? Change PasswordHow to change the password ? Service IdentificationChange Projector Address Change Language Reset Lamp RuntimeChange Baudrate PC Lamp Run Time History Lamp Drive ModeBarco logo Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNEWS76 SUNEWS67SUNXGA60 SUNXGA70Lens Cleaning Procedure Focusing the lensLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13875&966285&6