Barco R9001390 manual Change Password, How to enable or disable the password function ?

Page 49

Service Mode

Change Password

This item is password protected when the password strap is installed.

How to enable or disable the password function ?

The password function is enabled when the password strap on the controller module is installed.

To get access to the controller module, proceed as follows :

-Power down the projector and disconnect the power cord from the wall outlet.

-Turn both lock screws on the side of the front top cover with a screwdriver or coin counter clockwise.

-Lift up and pivot the top cover. Attention : the cover is not secured with an incorporated support. When opening, turn it over slowly and lay it down on the second part of the top cover.

Loosen the locking screws.

0 I

 

PROJECTORMODE :

 

 

 

GREEN - OPERATION

DIAGNOSTICS

 

COMMUNICATION PORT

RED - STANDBY

IR-ACKNOWLEDGED CODE

IR-RECEIVER

RS232 OUT

RS232 IN

(800-PERIPHERALS) REMOTE

IR-RECEIVED

R

G

B

H

V

R

G

B

H / C

V

R

G

B

H / C

V

27910

 

 

 

 

 

 

 

 

 

On

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

98

Open the top cover

When the strap is on leg 2-3 or no strap is mounted, the password function is enabled, when the strap is on leg 1-2, the password function is disabled.

0 I

 

PROJECTORMODE :

 

 

 

GREEN - OPERATION

DIAGNOSTICS

 

COMMUNICATION PORT

RED - STANDBY

IR-ACKNOWLEDGED CODE

IR-RECEIVER

RS232 OUT

RS 232 IN

(800-PERIPHERALS) REMOTE

 

 

 

 

 

 

 

 

 

 

IR-RECEIVED

R

G

B

H

V

R

G

B

H / C

V

R

G

B

H / C

V

9827910

 

 

 

 

 

 

 

 

 

 

On

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Password enabled

Password disabled

strap on leg 2-3

strap on leg 1-2

How to change the password ?

Highlight Change password by pushing the control disc up or down and press ENTER to display the Change Password menu.

ENTER displays the Change Password menu

EXIT returns to the adjustment selection menu.

ADJUST returns to operational mode.

The old password is displayed and can be changed by entering the digit with the numeric keys of the RCU or local keypad.

Press ENTER to save the new entered password. Press EXIT if no changes have to be made.

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE

CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY

LAMP DRIVE MODE

MORE...

Select with

or

 

then <ENTER>

 

<EXIT> to

CHANGE PASSWORD

 

 

Enter new

password

 

0000

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

5975938 BARCOREALITY 9200TCR+ 020798

 

10-3

 

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Reality 9200 TCR+ Page Date Art. No 020798 R5975938 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 10-1 Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?Componentvideo Separate SyncFront Panel Terminology Location and Functions of ControlControl Panel Terminology a. Local keypad RCU Remote controlConfiguration OSD Color InstallationFRONT/TABLE Installation Set Up Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byLamp Run Time Input ConnectionsFixed RGB analog input slot Periphiral Convergence Configuration Input SlotsEnter Input SlotsFixed 5-Input Slot slot Peripheral Convergence ConfigurationRgbhv Rgbs Video269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module Component Input Module Guided Random Access2032117B-Y S9,2,1387 RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting a Rcvds 05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorControlling How to Use the RCU?Projector Address How to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access BrightnessAdjustment Mode Start UP of the Adjustment ModeRandom Access Installation Service PasswordStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Load File File ServiceEdit File LoadPeriod Horizontal Total Pixels ActiveVertical Field Total LinesConfirm Edit File Edit File OptionsCopy RenameRename CopyDelete Picture TuningFile Options CTI ON/OFFStill Video Color TemperatureCTI on Still Video onDecoding EBU/IRE GammaDynamic Color Depth Noise ReductionGeometry Edge EnhancementShift GeometrySide Keystone SizeSize Side KeystoneOptions BlankingBlanking Random Access Adjustment Mode Input Slots Starting up the Installation ModeTroubleshooting How to AdjustPeripheral ConvergenceGreen to Midposition Green FocusingBlue on Green convergence Hatch Red on Green convergenceAbout Moca No Signal BLACK/BLUE ConfigurationOSD color On-Screen Display Internal PatternsInstallation Mode Starting up the Service Mode Service ModeService Identification IdentificationHow to enable or disable the password function ? Change PasswordHow to change the password ? Service IdentificationChange Projector Address Change Language Reset Lamp RuntimeChange Baudrate PC Lamp Run Time History Lamp Drive ModeBarco logo Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNEWS76 SUNEWS67SUNXGA60 SUNXGA70Lens Cleaning Procedure Focusing the lensLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13875&966285&6
Top Page Image Contents