Barco R9001390 manual Set up of the Baud Rate for Communication with a Computer

Page 24

Connections

Connecting a Computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector.

The projector has a RS232 port that allows it to communicate with a computer.

Applications : remote control and data communications.

a)remote control :

-easy adjustment of projector via IBM PC (or compat- ible) or MAC connection.

-allow storage of multiple projector configurations and set ups.

-wide range of control possibilities.

-address range from 0 to 255.

b)data communications :

-sending data to the projector or copying the data from the projector to a hard memory device.

Set up of the Baud Rate for Communication with a Computer.

See 'Change Baudrate PC' in chapter 'Service mode'.

Connecting a RCVDS 05 to the projector.

-Up to 20 inputs with the RCVDS 05 and 90 inputs when RCVDS's are linked via the expansion module.

-Serial communication with the projector.

-Remote control buttons on the RCVDS to control the projector (source selection and analog settings).

-The selected source number will be displayed on a 2 digit display and the selected input module will be indicated with a LED on the rear.

For more information about the use of : the RCVDS 05, consult the

owner's manual, order number : R5975765.

Connecting a VS05 to the projector

The VS05 can switch up to 5 Composite Video sources, 3 Super Video sources and 1 RGB analog or component video source to the projector. In addition, the audio signal proper to the source, can be switched to an audio amplifier.

Order number : R9827890

For more information about the use of the VS05, consult the VS05 owner's manual, BARCO order number : R5975245.

 

PROJECTOR MODE :

 

 

 

GREEN - OPERATION

DIAGNOSTICS

 

COMMUNICATION PORT

RED - STANDBY

IR-ACKNOWLEDGED CODE

IR-RECEIVER

RS232 OUT

RS 232IN

(800-PERIPHERALS) REMOTE

SDI IN

SDI OUT

IR-RECEIVED

R

G

B 56FRQQHFWLRQ￿￿￿VG

B

H / C

V

6￿9,'(29,'(9,'(2￿,1387

R

G

B

H / C

V

9827910

 

 

 

 

 

 

 

On

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting an IR Remote Receiver 800 to the projector.

This infrared receiver unit makes it possible to control the projector

 

from another room.

 

There is a communication line cable between the IR receiver and the

 

 

projector or the RCVDS. The control information from the RCU can

Screen

now be sent to the IR Remote Receiver 800.

The IR Remote Receiver 800 displays the selected source on a 7-

 

segment display.

 

Order number : R9827515.

 

Communication cable

IR Remote Receiver 800

Projector

Projection room

Control room

5-10

 

5975938 BARCOREALITY 9200TCR+ 020798

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Reality 9200 TCR+ Page Barco Projection Systems Date Art. No 020798 R5975938Federal communication commission FCC statement Table of Contents 10-1 Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?Componentvideo Separate SyncLocation and Functions of Control Front Panel TerminologyControl Panel Terminology a. Local keypad Remote control RCUInstallation Configuration OSD ColorFRONT/TABLE Installation Set Up AC Power mains cord connection Switching onConnections FusesSwitching to Stand-by Switching OffLamp Run Time Input ConnectionsPeriphiral Convergence Configuration Input Slots Fixed RGB analog input slotEnter Input SlotsPeripheral Convergence Configuration Fixed 5-Input Slot slotRgbhv Rgbs VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Guided Random Access Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQSet up of the Baud Rate for Communication with a Computer Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingProjector Address How to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access BrightnessStart UP of the Adjustment Mode Adjustment ModeRandom Access Installation Service PasswordStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service File Service Load FileEdit File LoadHorizontal Total Pixels Active PeriodVertical Field Total LinesEdit File Options Confirm Edit FileRename CopyRename CopyPicture Tuning DeleteFile Options CTI ON/OFFColor Temperature Still VideoCTI on Still Video onGamma Decoding EBU/IREDynamic Color Depth Noise ReductionEdge Enhancement GeometryShift GeometrySize Side KeystoneSize Side KeystoneBlanking OptionsBlanking Random Access Adjustment Mode Starting up the Installation Mode Input SlotsHow to Adjust TroubleshootingPeripheral ConvergenceGreen Focusing Green to MidpositionBlue on Green convergence Red on Green convergence HatchAbout Moca Configuration No Signal BLACK/BLUEOSD color On-Screen Display Internal PatternsInstallation Mode Service Mode Starting up the Service ModeService Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Service IdentificationReset Lamp Runtime Change Projector Address Change LanguageChange Baudrate PC Lamp Drive Mode Lamp Run Time HistoryBarco logo Panel Adjustments Preset Input BalancePreset Input Balance I2C diagnosisStandard Source SET UP Files SUNEWS67 SUNEWS76SUNXGA60 SUNXGA70Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13875&966285&6
Top Page Image Contents