Barco R9001390 manual Identification

Page 48

Service Mode

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY LAMP DRIVE MODE MORE...

Select with or then <ENTER> <EXIT> to return.

PANEL ADJUSTMENT

Select the

color temperature

PROJECTOR WHITE

6500

Select with or then <ENTER> <EXIT> to return.

PRESET INPUT BALANCE

WHITE BALANCE

BLACK BALANCE

DEFAULT

Select with <ENTER>

<EXIT> to return

Adjust

red with or

blue with or

SERVICE

BARCO LOGO

PANEL ADJUSTMENTS

PRESET INPUT BALANCE

I2C DIAGNOSIS

MORE...

Select with or then <ENTER> <EXIT> to return.

BARCO LOGO

STATUS :

BACKGROUND :

SHIFT

HOT KEY :

Select with or <ENTER> to toggle/select <EXIT> to return.

I2C DIAGNOSIS

 

 

 

 

 

D CA

LCD DRIVER

SC76013

E4H # # #

LCD DRIVER

SC76013

E6H # # #

LCD DRIVER

SC76013

E8H # # #

LCD DRIVER

SC76013

EAH # # #

INPUT SELECT

TDA8444

46H

# # #

INPUT SELECT

PCF8574A 7EH # # #

DECODER

87C751

12H

# # #

LAMP DRIVER

PCF8574A

72H

# # #

POWER SUPPLY 87C752

10H

# # #

Identification

To display the Identification screen, push the control disc up or down to highlight Identification and press ENTER to display the Identifica- tion screen.

The Identification screen gives an overview of :

-type of projector

-projector address

-software version

-installation configuration

-baud rate

-text ON

-projector serial number

-projector run time

-type of projector : BARCOREALITY 9200 TCRPLUS

-software version

-Proj. Address : to change the address of the projector, see Change Projector Address in this chapter.

-Installation : possible installations :

*Front/Ceiling

*Front/Table

*Rear/Ceiling

*Rear/Table

To change the installation configuration follow the instructions in chapter Installation Set Up.

-Baud rate : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult 'Change Baudrate PC' in this chapter.

-Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours.

-Projector Serial number : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE

CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY

LAMP DRIVE MODE

MORE...

Select with or then <ENTER> <EXIT> to return.

10-2

 

5975938 BARCOREALITY 9200TCR+ 020798

 

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Reality 9200 TCR+ Page Barco Projection Systems Date Art. No 020798 R5975938Federal communication commission FCC statement Table of Contents 10-1 Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?Componentvideo Separate SyncLocation and Functions of Control Front Panel TerminologyControl Panel Terminology a. Local keypad Remote control RCUInstallation Configuration OSD ColorFRONT/TABLE Installation Set Up AC Power mains cord connection Switching onConnections FusesSwitching to Stand-by Switching OffLamp Run Time Input ConnectionsPeriphiral Convergence Configuration Input Slots Fixed RGB analog input slotEnter Input SlotsPeripheral Convergence Configuration Fixed 5-Input Slot slotRgbhv Rgbs VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Guided Random Access Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQSet up of the Baud Rate for Communication with a Computer Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingProjector Address How to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access BrightnessStart UP of the Adjustment Mode Adjustment ModeRandom Access Installation Service PasswordStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service File Service Load FileEdit File LoadHorizontal Total Pixels Active PeriodVertical Field Total LinesEdit File Options Confirm Edit FileRename CopyRename CopyPicture Tuning DeleteFile Options CTI ON/OFFColor Temperature Still VideoCTI on Still Video onGamma Decoding EBU/IREDynamic Color Depth Noise ReductionEdge Enhancement GeometryShift GeometrySize Side KeystoneSize Side KeystoneBlanking OptionsBlanking Random Access Adjustment Mode Starting up the Installation Mode Input SlotsHow to Adjust TroubleshootingPeripheral ConvergenceGreen Focusing Green to MidpositionBlue on Green convergence Red on Green convergence HatchAbout Moca Configuration No Signal BLACK/BLUEOSD color On-Screen Display Internal PatternsInstallation Mode Service Mode Starting up the Service ModeService Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Service IdentificationReset Lamp Runtime Change Projector Address Change LanguageChange Baudrate PC Lamp Drive Mode Lamp Run Time HistoryBarco logo Panel Adjustments Preset Input BalancePreset Input Balance I2C diagnosisStandard Source SET UP Files SUNEWS67 SUNEWS76SUNXGA60 SUNXGA70Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13875&966285&6
Top Page Image Contents