Barco R9001390 manual Source numbers 81

Page 58

Source Numbers 80 - 89 and 90 - 99

Source numbers 81 - 85

Only valid if no input module is connected to slot 81 - 85 of a RCVDS05.

The source numbers 81 - 85 correspond to the physical inputs 1 - 5 of the projector. e.g. When slot 1 of the projector has to be selected, key in source number 81.

The relationship between the sources of slot 1 - 5 of the projector with 800 peripheral is shown in the table below.

source of slot 1 source of slot 2 source of slot 3 source of slot 4 source of slot 5

source number 81 source number 82 source number 83 source number 84 source number 85

C-2		5975738 BARCOREALITY 9200TCR+ 020798

Image 58

Contents Reality 9200 TCR+ Page Barco Projection Systems Date Art. No 020798 R5975938Federal communication commission FCC statement Table of Contents 10-1 Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncFront Panel Terminology Location and Functions of ControlControl Panel Terminology a. Local keypad Remote control RCUConfiguration OSD Color InstallationFRONT/TABLE Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsEnter Periphiral Convergence Configuration Input SlotsFixed RGB analog input slot Input SlotsRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Component Input Module Guided Random Access2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorControlling How to Use the RCU?Projector Address Picture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? BrightnessRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Edit File File ServiceLoad File LoadVertical Field Total Horizontal Total Pixels ActivePeriod LinesEdit File Options Confirm Edit FileRename RenameCopy CopyFile Options Picture TuningDelete CTI ON/OFFCTI on Color TemperatureStill Video Still Video onDynamic Color Depth GammaDecoding EBU/IRE Noise ReductionShift Edge EnhancementGeometry GeometrySize SizeSide Keystone Side KeystoneOptions BlankingBlanking Random Access Adjustment Mode Starting up the Installation Mode Input SlotsPeripheral How to AdjustTroubleshooting ConvergenceGreen to Midposition Green FocusingBlue on Green convergence Hatch Red on Green convergenceAbout Moca OSD color On-Screen Display ConfigurationNo Signal BLACK/BLUE Internal PatternsInstallation Mode Starting up the Service Mode Service ModeService Identification IdentificationHow to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationChange Projector Address Change Language Reset Lamp RuntimeChange Baudrate PC Lamp Run Time History Lamp Drive ModeBarco logo Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Lens Cleaning Procedure Focusing the lensLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13875&966285&6