Barco R9001390 manual Size, Side Keystone

Page 38

Random Access Adjustment Mode

Size

Highlight Size by pushing the control disc up or down and press ENTER to select.

The size can be adjusted in a vertical or horizontal way. When adjusting the vertical size,

The upper side of the image is fixed (table and ceiling mounted configurations) and only the lower side can be moved to its exact position.

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

OPTIONS

Select with

or

then <ENTER>

<EXIT> to

return.

When adjusting the horizontal size, the left side of the image is fixed and only the right side can be moved to its exact position.

Fixed sides

Horizontal size

adjustment

Side Keystone

Highlight Side Keystone by pushing the control disc up or down and press ENTER to select.

The side keystone adjustment is used to align the image if the projector is mounted at a non-standard projection angle.

Push the control disc to the right or to the left to adjust the keystone of the image.

When the upper part of the image is wider than the lower part of the image, push the control disc to the left. The number indication below the bar scale will be negative.

When the upper part of the image is smaller than the lower part of the image, push the control disc to the right. The number indication below the bar scale will be positive.

Vertical size adjustment

Example for table mount configuration

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

OPTIONS

Select with

or

then <ENTER>

<EXIT> to

return.

8-10

 

5975938 BARCOREALITY 9200TCR+ 020798

 

Image 38
Contents Reality 9200 TCR+ Page Barco Projection Systems Date Art. No 020798 R5975938Federal communication commission FCC statement Table of Contents 10-1 Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncControl Panel Terminology a. Local keypad Location and Functions of ControlFront Panel Terminology Remote control RCUFRONT/TABLE InstallationConfiguration OSD Color Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsEnter Periphiral Convergence Configuration Input SlotsFixed RGB analog input slot Input SlotsRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module 2032117B-Y S9,2,1387 Guided Random AccessComponent Input Module 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector Address How to Use the RCU?Controlling Picture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? BrightnessRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordStart up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Edit File File ServiceLoad File LoadVertical Field Total Horizontal Total Pixels ActivePeriod LinesEdit File Options Confirm Edit FileRename RenameCopy CopyFile Options Picture TuningDelete CTI ON/OFFCTI on Color TemperatureStill Video Still Video onDynamic Color Depth GammaDecoding EBU/IRE Noise ReductionShift Edge EnhancementGeometry GeometrySize SizeSide Keystone Side KeystoneBlanking BlankingOptions Random Access Adjustment Mode Starting up the Installation Mode Input SlotsPeripheral How to AdjustTroubleshooting ConvergenceBlue on Green convergence Green FocusingGreen to Midposition About Moca Red on Green convergenceHatch OSD color On-Screen Display ConfigurationNo Signal BLACK/BLUE Internal PatternsInstallation Mode Service Service ModeStarting up the Service Mode Identification IdentificationHow to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationChange Baudrate PC Reset Lamp RuntimeChange Projector Address Change Language Barco logo Lamp Drive ModeLamp Run Time History Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Lenses Focusing the lensLens Cleaning Procedure Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13875&966285&6