Barco R9001390 Start UP of the Adjustment Mode, Random Access Installation Service, Password

Page 27

Start up of the Adjustment Mode

7START UP OF THE ADJUSTMENT MODE

Adjustment Mode

All source parameters, picture tuning and geometry are made while in the 'Adjustment Mode'

. Press the ADJUST or ENTER key to enter the 'Adjustment mode'.

You are now in the 'Adjustment Mode'. The control disk (RCU) or '+ or '-' keys (local keypad) are used to make menu selections and also for adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used to terminate the adjustment mode while any path selection menu is displayed.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS INSTALLATION SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return.

There are 3 possible paths to follow once in the Adjustment Mode. They are :

Installation - Installation should be selected if a new input module is installed or a new source is connected to an existing input module. Also when the projector is relocated in a new configuration.

Random Access - Random Access should be selected to set up a new source.

Service - Service should be selected if the user intends to change general settings such as password, language, address, etc.or some service actions as reset lamp run time, panel adjustments, etc. or get set-up information.

Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password (Password protection is only available when the password strap on the controller module is ON, see 'Change password' in chapter 10 : 'Service mode'.

Your password contains 4 digits.

Enter the digits with the numeric keys.

Example : 2 3 1 9

The first digit position is highlighted. Enter with the numeric keys. The highlighted square jumps to the next position. Continue until all 4 digits are filled in.

When your password is correct, you gain access to the selected item.

When your password is wrong. The error message "Invalid password" is displayed on the screen. Press EXIT to continue and to return to the Service menu.

Factory programmed password : 0 0 0 0

Once the password is correctly entered, all other password protected items are accessible without re-entering your password.

When re-entering the Adjustment mode, it will be nessary to enter your password again when selecting a password protected item.

PASSWORD

ENTER PASSWORD

----

Use numeric keys

<EXIT> to return

Error

 

Invalid

password

<EXIT>

to return

5975109 BARCOREALITY 9200TCR+ 020798

 

7-1

 

Image 27
Contents Reality 9200 TCR+ Page Date Art. No 020798 R5975938 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 10-1 Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Separate Sync Where to install the projector?How to install a projection lens? ComponentvideoLocation and Functions of Control Front Panel TerminologyControl Panel Terminology a. Local keypad RCU Remote controlInstallation Configuration OSD ColorFRONT/TABLE Installation Set Up Fuses AC Power mains cord connectionSwitching on ConnectionsInput Connections Switching to Stand-bySwitching Off Lamp Run TimeInput Slots Periphiral Convergence Configuration Input SlotsFixed RGB analog input slot EnterVideo Peripheral Convergence ConfigurationFixed 5-Input Slot slot Rgbhv Rgbs269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module Guided Random Access Component Input Module2032117B-Y S9,2,1387 RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting an IR Remote Receiver 800 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorHow to Use the RCU? ControllingProjector Address Brightness How to Display a Projector Address?How to Program an Address into the RCU? Picture Controls with Direct AccessPassword Start UP of the Adjustment ModeAdjustment Mode Random Access Installation ServiceStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Load File ServiceLoad File Edit FileLines Horizontal Total Pixels ActivePeriod Vertical Field TotalConfirm Edit File Edit File OptionsCopy RenameCopy RenameCTI ON/OFF Picture TuningDelete File OptionsStill Video on Color TemperatureStill Video CTI onNoise Reduction GammaDecoding EBU/IRE Dynamic Color DepthGeometry Edge EnhancementGeometry ShiftSide Keystone SizeSide Keystone SizeBlanking OptionsBlanking Random Access Adjustment Mode Input Slots Starting up the Installation ModeConvergence How to AdjustTroubleshooting PeripheralGreen Focusing Green to MidpositionBlue on Green convergence Red on Green convergence HatchAbout Moca Internal Patterns ConfigurationNo Signal BLACK/BLUE OSD color On-Screen DisplayInstallation Mode Service Mode Starting up the Service ModeService Identification IdentificationService Identification Change PasswordHow to enable or disable the password function ? How to change the password ?Reset Lamp Runtime Change Projector Address Change LanguageChange Baudrate PC Lamp Drive Mode Lamp Run Time HistoryBarco logo I2C diagnosis Panel AdjustmentsPreset Input Balance Preset Input BalanceStandard Source SET UP Files SUNXGA70 SUNEWS67SUNEWS76 SUNXGA60Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13875&966285&6