Barco R9001390 manual Starting up the Installation Mode, Input Slots

Page 41

Installation Mode

9

INSTALLATION MODE

 

Starting up the Installation Mode

Push the control disc up or down to highlight Installation and then press ENTER.

ENTER continues to the Installation mode selection menu. EXIT returns to operational mode.

The following item can be selected in the Installation mode :

Input slots : to set up the input priority.

800 Peripheral : to select the type of output module used in the RCVDS05.

Convergence : to align the red, green and blue image.

Configuration : to set up the projector position.

OSD color : to change the color of the highlighted item.

No Signal : to display a black or blue screen when no source is connected to the projector.

Internal Patterns

Input Slots

Highlight Input Slots by pushing the control disc up or down and press

ENTER.

The internal system will scan the input slots and displays the result in the Input Slots menu.

Source

indication

Video or S-Video

Video[Video]

 

Video[S-Video]

RGB analog

RGB-SS[CV] : separate sync is composite video

 

signal on H/C input

 

RGB-SS[CS or HS&VS] : separate sync is

 

composite sync or horizontal and vertical

 

sync

 

RGB-SOG : sync on green

Component video

Component Video - SS : component video

 

with separate sync

 

Component Video - SOY : component video

 

with sync on Y

 

Component Video - 3LSS : component video

 

with 3 level separate sync.

 

Component Video - 3LSOY : component

 

video with 3 level sync on Y.

RGB analog with

 

tri-level sync

RGB3L-SS : RGB with separate Tri level sync

 

RGB3L-SOG : RGB with Tri level sync on

 

green

For slot 1 and slot 2, see chapter 'Connections'

If a RCVDS (switched on) or VS05 is connected to the projector, it will be also indicated on the menu by adding +800 peripheral. If no 800 peripheral indication is made on the menu, there are still two possi- bilities :

-no RCVDS or VS05 connected or

-RCVDS is switched off.

When a 800 peripheral is connected to the projector, the input slots are not accessible with the control disc to toggle their function.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

OSD COLOR

NO SIGNAL [BLACK] INTERNAL PATTERNS

Select with or

then <ENTER>

<EXIT> to return.

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

OSD COLOR

NO SIGNAL [BLACK] INTERNAL PATTERNS

Select with

or

then <ENTER>

<EXIT>

INPUT SLOTS

1. RGB-SS [CV]

2. RGB-SOG

3. Video [Video]

4. Component Video

5975938 BARCOREALITY 9200TCR+ 020798

 

9-1

 

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Reality 9200 TCR+ Page Date Art. No 020798 R5975938 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 10-1 Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?Componentvideo Separate SyncControl Panel Terminology a. Local keypad Location and Functions of ControlFront Panel Terminology RCU Remote controlFRONT/TABLE InstallationConfiguration OSD Color Installation Set Up Switching on AC Power mains cord connectionConnections FusesSwitching Off Switching to Stand-byLamp Run Time Input ConnectionsFixed RGB analog input slot Periphiral Convergence Configuration Input SlotsEnter Input SlotsFixed 5-Input Slot slot Peripheral Convergence ConfigurationRgbhv Rgbs Video269,2VIDEO,1387 Video/S-video Input ModuleRGB Analog Input Module 2032117B-Y S9,2,1387 Guided Random AccessComponent Input Module RGB3S / RG3sB Input Module 16HSDRUP UD \6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQ Serial Digital Input slotConnecting a Rcvds 05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector Address How to Use the RCU?Controlling How to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access BrightnessAdjustment Mode Start UP of the Adjustment ModeRandom Access Installation Service PasswordStart up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Load File File ServiceEdit File LoadPeriod Horizontal Total Pixels ActiveVertical Field Total LinesConfirm Edit File Edit File OptionsCopy RenameRename CopyDelete Picture TuningFile Options CTI ON/OFFStill Video Color TemperatureCTI on Still Video onDecoding EBU/IRE GammaDynamic Color Depth Noise ReductionGeometry Edge EnhancementShift GeometrySide Keystone SizeSize Side KeystoneBlanking BlankingOptions Random Access Adjustment Mode Input Slots Starting up the Installation ModeTroubleshooting How to AdjustPeripheral ConvergenceBlue on Green convergence Green FocusingGreen to Midposition About Moca Red on Green convergenceHatch No Signal BLACK/BLUE ConfigurationOSD color On-Screen Display Internal PatternsInstallation Mode Service Service ModeStarting up the Service Mode Identification IdentificationHow to enable or disable the password function ? Change PasswordHow to change the password ? Service IdentificationChange Baudrate PC Reset Lamp RuntimeChange Projector Address Change Language Barco logo Lamp Drive ModeLamp Run Time History Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNEWS76 SUNEWS67SUNXGA60 SUNXGA70Lenses Focusing the lensLens Cleaning Procedure Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13875&966285&6
Top Page Image Contents