Barco R9001390 manual Battery installation in the RCU

Page 8

Unpacking and Dimensions

Battery installation in the RCU.

A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power cord. To install the battery, remove the battery cover on the backside of the remote control by pushing the indicated handle a little towards the bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).

Insert the new 9 V battery (type E-block or equivalent) in the lower compartment and connect the battery to the contact plate.

Insert the battery into the lower compartment and put the cover back.

Note : projector address has to be programmed on the RCU before using the RCU (see chapter 'Controlling').

Contact plate

Battery

fig.1

Insert here the 'Insert card RCU' which you can cut out on the last page of this manual.

fig.2

310a.DRW

1-2

 

5975938 BARCOREALITY 9200TCR+ 020798

 

Image 8
Contents Reality 9200 TCR+ Page Barco Projection Systems Date Art. No 020798 R5975938Federal communication commission FCC statement Table of Contents 10-1 Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?Componentvideo Separate SyncControl Panel Terminology a. Local keypad Location and Functions of ControlFront Panel Terminology Remote control RCUFRONT/TABLE InstallationConfiguration OSD Color Installation Set Up AC Power mains cord connection Switching onConnections FusesSwitching to Stand-by Switching OffLamp Run Time Input ConnectionsPeriphiral Convergence Configuration Input Slots Fixed RGB analog input slotEnter Input SlotsPeripheral Convergence Configuration Fixed 5-Input Slot slotRgbhv Rgbs VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module 2032117B-Y S9,2,1387 Guided Random AccessComponent Input Module 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQSet up of the Baud Rate for Communication with a Computer Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector Address How to Use the RCU?Controlling How to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access BrightnessStart UP of the Adjustment Mode Adjustment ModeRandom Access Installation Service PasswordStart up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode File Service Load FileEdit File LoadHorizontal Total Pixels Active PeriodVertical Field Total LinesEdit File Options Confirm Edit FileRename CopyRename CopyPicture Tuning DeleteFile Options CTI ON/OFFColor Temperature Still VideoCTI on Still Video onGamma Decoding EBU/IREDynamic Color Depth Noise ReductionEdge Enhancement GeometryShift GeometrySize Side KeystoneSize Side KeystoneBlanking BlankingOptions Random Access Adjustment Mode Starting up the Installation Mode Input SlotsHow to Adjust TroubleshootingPeripheral ConvergenceBlue on Green convergence Green FocusingGreen to Midposition About Moca Red on Green convergenceHatch Configuration No Signal BLACK/BLUEOSD color On-Screen Display Internal PatternsInstallation Mode Service Service ModeStarting up the Service Mode Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Service IdentificationChange Baudrate PC Reset Lamp RuntimeChange Projector Address Change Language Barco logo Lamp Drive ModeLamp Run Time History Panel Adjustments Preset Input BalancePreset Input Balance I2C diagnosisStandard Source SET UP Files SUNEWS67 SUNEWS76SUNXGA60 SUNXGA70Lenses Focusing the lensLens Cleaning Procedure Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13875&966285&6