Barco R9001390 manual Peripheral, Convergence, How to Adjust, Troubleshooting

Page 42

Installation Mode

800 Peripheral

When a RCVDS05 is connected to the projector, the type of output module of this RCVDS05 has to be defined in the 800 peripheral menu.

The type of output module can be :

-standard output module or

-5 cable output module.

To define the output module, highlight "800 Peripheral" by pushing the control disc up or down and press ENTER to display the 800 peripheral menu.

Use the ENTER key to toggle between [standard] and [5 cable].

INSTALLATION

INPUT SLOTS

800 PERIPHERAL

CONVERGENCE

CONFIGURATION

OSD COLOR

NO SIGNAL [BLACK]

INTERNAL PATTERNS

Select with

or

then <ENTER>

<EXIT> to

800 PERIPHERAL

OUTPUT MODULE [STANDARD]

Convergence

Highlight "Convergence" by pushing the control disc up or down and press ENTER to display the convergence selection menu.

Every LCD panel has 6 motorized adjustments. These motorized adjustments can be adjusted with your RCU in your hand, while you are standing next to the screen. By changing the position of these servo motors, you change the relative position of the panels and converge the image.

Always start with the adjustment of the green panel. When the green image is correctly focused, it will later on be used as the reference image to converge the red and blue image.

The following alignments have to be done :

You have to adjust the green panel until the indicated lines on the screen are focused (sharp lines). Continue with the blue panel and adjust until the blue lines coincide with the green lines. Than continue with the red panel until the red lines coincide with the green lines.

If there is a total misalignment of the convergence or when the panels are replaced, start with green to midposition and continue then with the normal alignment of Green, Blue on green and Red on green.

How to Adjust

The possible adjustments are shown on the screen with a drawing which indicates the effect of the adjustment and a digit for 1 to 7. Adjustment 7 combines automatically adjustment 1, 2 and 3 in order to enlarge or reduce the complete image (see drawing)

To activate an adjustment :

-press the corresponding digit on the RCU. The digit on the screen will be highlighted and

-adjust with the control disc.

Troubleshooting

For certain combinations of alignments 4, 5 and the horizontal alignment 6, it is possible that one of the alignments no longer adjusts or does not perform as expected. For example it the horizontal alignment 6 is in a extreme position it is possible that alignment 4 or 5 no longer functions or performs a vertical shift in stead of a rotation. The solution is to put all three above alignments in midpositon.

If it is impossible to obtain the correct position, your projector is not correctly positioned (see chapter Installation Guidelines).

INSTALLATION

 

INPUT SLOTS

 

800 PERIPHERAL

 

CONVERGENCE

 

CONFIGURATION

 

OSD COLOR [BLACK]

 

INTERNAL PATTERNS

 

Select with

or

 

then <ENTER>

 

<EXIT>

CONVERGENCE

 

GREEN TO MIDPOSITION

 

GREEN

 

 

BLUE ON GREEN

 

RED ON GREEN

 

HATCH

 

 

ABOUT MOCA

 

Select with

or

 

then <ENTER>

 

<EXIT> to return.

9-2

 

5975938 BARCOREALITY 9200TCR+ 020798

 

Image 42
Contents Reality 9200 TCR+ Page Barco Projection Systems Date Art. No 020798 R5975938Federal communication commission FCC statement Table of Contents 10-1 Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines Componentvideo Where to install the projector?How to install a projection lens? Separate SyncLocation and Functions of Control Front Panel TerminologyControl Panel Terminology a. Local keypad Remote control RCUInstallation Configuration OSD ColorFRONT/TABLE Installation Set Up Connections AC Power mains cord connectionSwitching on FusesLamp Run Time Switching to Stand-bySwitching Off Input ConnectionsEnter Periphiral Convergence Configuration Input SlotsFixed RGB analog input slot Input SlotsRgbhv Rgbs Peripheral Convergence ConfigurationFixed 5-Input Slot slot VideoVideo/S-video Input Module 269,2VIDEO,1387RGB Analog Input Module Guided Random Access Component Input Module2032117B-Y S9,2,1387 16HSDRUP UD \ RGB3S / RG3sB Input ModuleSerial Digital Input slot 6HSDUDWH--6\QFV-VHOHFWLRQ\QFRQJUHHQConnecting a VS05 to the projector Set up of the Baud Rate for Communication with a ComputerConnecting a Rcvds 05 to the projector Connecting an IR Remote Receiver 800 to the projectorHow to Use the RCU? ControllingProjector Address Picture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? BrightnessRandom Access Installation Service Start UP of the Adjustment ModeAdjustment Mode PasswordStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Edit File File ServiceLoad File LoadVertical Field Total Horizontal Total Pixels ActivePeriod LinesEdit File Options Confirm Edit FileRename RenameCopy CopyFile Options Picture TuningDelete CTI ON/OFFCTI on Color TemperatureStill Video Still Video onDynamic Color Depth GammaDecoding EBU/IRE Noise ReductionShift Edge EnhancementGeometry GeometrySize SizeSide Keystone Side KeystoneBlanking OptionsBlanking Random Access Adjustment Mode Starting up the Installation Mode Input SlotsPeripheral How to AdjustTroubleshooting ConvergenceGreen Focusing Green to MidpositionBlue on Green convergence Red on Green convergence HatchAbout Moca OSD color On-Screen Display ConfigurationNo Signal BLACK/BLUE Internal PatternsInstallation Mode Service Mode Starting up the Service ModeService Identification IdentificationHow to change the password ? Change PasswordHow to enable or disable the password function ? Service IdentificationReset Lamp Runtime Change Projector Address Change LanguageChange Baudrate PC Lamp Drive Mode Lamp Run Time HistoryBarco logo Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files SUNXGA60 SUNEWS67SUNEWS76 SUNXGA70Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13875&966285&6